Handloading the FN 5.7x28mm - Load Data
The FN 5.7x28mm cartridge (center) features a bottleneck case and utilizes .224-inch bullets. For size comparison the .357 Magnum (left) and .22 Winchester Magnum (right) are shown. Factory loads contain a 40-grain Hornady V-MAX bullet pushed with 5.1 grains of an unknown ball powder. Dies must be properly adjusted (see text) to avoid crushing ...
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Notes From the Lab: .300 Whisper / .300 AAC Blackout
loaddata.comAAC Blackout, a standar dized commercial version of the .300 Whisper. Whisper’s built after 1999 were dimensionally identical to the .300 Blackout and are fully interchangeable; however, the latter features a
Form, 300 aac blackout, Blackout, Whisper, 300 whisper, 300 blackout, From the lab
Handloading the 7.62x39mm - Load Data
loaddata.comlets with a muzzle velocity of 2,300 fps drop only an inch more. The Nosler 125-grain Ballistic Tip has a sleek shape, and with a velocity of 2,460 fps it drops about an inch less than the Sierra 110-grain bul-let, but an inch of drop either way at 200 yards is splitting pretty fine hairs. The 7.62x39 is commonly re-ferred to as somewhat less ...
Notes from the Lab: .243 Winchester - Load Data
loaddata.comFor handloading lightweight bullets weighing 58 through 75 grains, top performing (accuracy and velocity) powders included Hodgdon Varget, H-4895, Accurate AAC-2520, Alliant RL-15, Vihtavuori N-140, IMR-4064 and IMR-4831.
Form, Bullet, Winchester, Lightweight, 243 winchester, From the lab, Lightweight bullets
Handloading the AR-15 .223 with 1-in-9 Twist
loaddata.comto an overall cartridge length of 2.26 inches sits deeply in the .223 case (right), using up some of the powder capacity. The Sierra 65-grain spitzer boat- tail and 69-grain MatchKing HPBT gave excellent results in the AR-15 with a one-in-9-inch twist. Many loads proved capable of sub MOA accuracy from a sandbag rest.
Handloads - Load Data
loaddata.comHandloader 231 to any sane range. Most new rifles chambered for varmint cartridges will group five shots of factory am-munition into one inch or less at 100 yards, a phenomenon that would have astounded your grand-father. However, his grandson wants more. This is the human condition. If you really, really want to shoot itty-bitty groups, you ...
Burn rate Chart - Load Data
loaddata.com157) Norma N-204 158) Hodgdon Hybrid 100V 159) Vihtavuori N550 160) Alliant Reloder 19 161) IMR-4831 162) Ramshot Hunter 163) Scot Brig 4831 164) Norma N-205 165) Accurate 3100 166) Vihtavuori N160 167) Alliant Power Pro 4000 MR 168) Winchester WMR 169) Hodgdon H-4831 & H-4831sc 170) Hodgdon SUPERFORMANCE 171) IMR-4955 172) Winchester Supreme 780
Fastest . . . BURN RATE CHART - Load Data
loaddata.comFastest . . . BURN RATE CHART Slowest . . . 1) Norma R-1 2) Vihtavuori N-310 3) Hodgdon Titewad 4) ADI AS-30N 5) Accurate Nitro 100 6) Alliant Bullseye 7) Accurate Solo 1000
AutoComp - Load Data
loaddata.com45 ACP 185 GR. HDY 6.7 856 12,600 CUP 7.4 958 16,200 CUP 200 GR. LSWEC 6.5 843 11,500 CUP 7.2 914 15,100 CUP 200 GR. SPR 6.4 856 12,600 CUP 7.0 930 16,00 CUP 230 GR. HDY 6.0 789 13,800 CUP 6.6 871 17,100 CUP 230 GR. LRN 6.1 832 13,700 CUP 6.6 896 16,400 CUP www.wwpowder.com!" Shaded area is the additional Gas Volume available from AutoComp for …
Related documents
Ball Screw - THK
www.thk.comFeatures and Types Ball Screw Features of the Ball Screw Driving Torque One Third of the Sliding Screw With the Ball Screw, balls roll between the screw shaft and the nut to achieve high efficiency. Its required driving torque is only one third of the conv entional sliding screw. (See Fig.1 and Fig.2.) As a
Feature, Driving, Screw, Ball, Ball screws, Ball screw features of the ball screw driving
DESIGN OF AN AUTOMATIC DOOR SYSTEM FOR AN …
www.inist.orgBall screw guide driving the arm system ... The features of ATN introduce several requirements to the vehicle door system. Referring to existing operational ATN systems, it is not hard to find the vehicles usually have . system . 12 Door. Door. Automatic Door ...
PARTS LIST/ TECHNICAL GUIDE
www.seikoserviceusa.comwheel and pinion screw 0012485 [b cal. :0012420] 16 cannon pinion 0225414 [b cal. :0225005] 15 minute wheel and pinion 0261183[b cal.:0261006] 14 date driving wheel 0802183 [b cal. :0802300] 13 intermediate date driving wheel and pinion 0817300 3 snap for day star with dial disk 0963300 7 date dial guard screw a (1 pic)0012354[b cal.:0016705]
CONTINENTAL STEEL PRODUCTS HANDBOOK
www.consteel.com.sg- Electro-mechanical drill feed using ball bearing spindle with servo motor - Automatic cross-section measuring - Fast and precise drill spindles positioning via ball screw drive and servo motors. The Control Desk with graphical user interface under Windows and Touch-Screen Monitors ensures a fast and easy programming of the machine.
5-PHASE STEPPING SYSTEMS - SANYO DENKI
www.sanyodenki.comThis driver features approximately 30% less vibration compared with our conventional product* (when used with an AC input driver). Also, a low-vibration mode function provides smooth driving, even with one-division (full step) and two-division (half step) coarse resolution settings. This allows vibrations to be suppressed
Ford Meter Box Catalog - Section A
assets.fordmeterbox.comA-4 Drilling Machine Adapters Recommended Drilling Machine Adapters Size Ford Corporation Stop number outlet thread mueller romaC ridgid reed Ford e-4 & e-5 d-4 & d-5 tapmate too mlt3401 dm1100 model 77 Simtap Flare Copper thread outlet 1/2" F600-1, F700-1 , F1000-1(-Q), F1100-1 1/2" Fl . Copper 63796 - - - - DMA2-1-NL -