Intershield 300 - AkzoNobel

Dec 04, 2015 · For use in Marine situations in North America, the following surface preparation standards can be used: SSPC-SP10 in place of Sa2½ (ISO 8501-1:2007) SSPC-SP6 in place of Sa2 (ISO 8501-1:2007) SSPC-SP11 in place of Pt3 (JSRA SPSS:1984) Page 2 of 4 Ref:223 Issue Date:04/12/2015 Marine Coatings

  Standards, Coating, Sspc

Intergard 821 - AkzoNobel

Dec 04, 2015 · contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. SURFACE PREPARATIONS ANODE SHIELDS NEWBUILDING/MAJOR REFURBISHMENT Where necessary, remove weld spatter and smooth weld seams and sharp edges. Abrasive blast clean to Sa2½ (ISO 8501-1:2007). If oxidation has occurred between …

  Cleaning, Solvents, Sspc, Sspc sp1 solvent cleaning

Intergard 740 - AkzoNobel

Nov 23, 2015 · Consult your International Paint representative for the system best suited for the surfaces to be protected. SYSTEMS AND COMPATIBILITY ... .Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO 8501-1:2007) and primed prior to the application of Intergard 740 ... For use in Marine situations in North ...

  Area, Marines, Protected

Interthane 990 - AkzoNobel

May 25, 2016 · relevant national Health, Safety & Environmental standards and regulations. Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels.

  Sheet, Data, Safety, Material, Material safety data sheet

Interzinc 22 - AkzoNobel

Sep 02, 2016 · Interzinc 22, the surface should be reblasted to the specified visual standard. Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner. A surface profile of 40-75 microns is recommended. Consult your International Paint representative for specific recommendations. NOTE

  Interzinc

Interlac 665 - AkzoNobel

Nov 13, 2015 · Marine Coatings. Interlac 665 Alkyd Finish Interlac 665 is not suitable for use on immersed areas. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations.

  Coating

Interseal 670HS - AkzoNobel

Nov 13, 2017 · Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and ... Vol Pack Vol Pack ... Low Temperature - Global Epoxy Primer Interseal 0 13/11/2017 Interseal 670HS Interseal 670HS - Low ...

  Sheet, Data, Safety, Material, Material safety data sheet

Intertherm 50 - AkzoNobel

Feb 04, 2015 · For use at Newbuilding, Maintenance & Repair or On Board Maintenance. INTENDED USES HTA097-Aluminium, HTA099-Black 45% (ISO 3233:1998) 25 microns dry (56 microns wet) 18 m²/litre at 25 microns dft, allow appropriate loss factors Airless Spray, Brush, Conventional Spray, Roller PRODUCT INFORMATION Volume Solids Typical Film Thickness ...

  Information, Maintenance, Intertherm, Intertherm 50

Intergard 269 - AkzoNobel

Mar 11, 2016 · 20 lt 16 lt 20 lt 4 lt 5 lt 5 US gal 4 US gal 5 US gal 1 US gal 1 US gal UNIT SHIPPING WEIGHT (TYPICAL) Unit Size Unit Weight 20 lt 32.9 Kg 5 US gal 68.4 lb Shelf Life 12 months minimum at 25°C. Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition. STORAGE EGA042-Light Grey available in ...

Intergard 263 - AkzoNobel

May 12, 2017 · Spot Repair - The Intertuf 262/Intergard 263 system may be used for the spot repair of existing epoxy, coal tar epoxy, chlorinated rubber, vinyl tar and tar-free vinyl substrates. Feathered overlap areas must be kept to a minimum. Consult International Paint. The Intertuf 262/Intergard 263 system is not suitable for repair of bituminous substrates.

  Paint, Cola, Coal tar

Surface Preparation Standard No. 1 - .NET Framework

SSPC-SP 1 1 es s 1 1 1 SSPC: The Society for Protective Coatings Surface Preparation Standard No. 1 Solvent Cleaning 1. Scope 1.1 This standard defines the end-condition of a metal surface from which visible deposits of oil, grease, and other visible contaminants have been removed in preparation for

  Standards, Preparation, Sspc, Preparation standard

MAIN TYPES OF PAINT USED WITH STEEL: STANDARDS ...

and twelve months, respectively. Note that the 2-75 standard specifies that the steel must be prepared before painting in compliance with SSPC standard SP7-63 Brush-off Blast Cleaning (Article 4.1 – Surface Preparation). Alkyd primers are usually grey but may also be available in red and white. Contrary to

  Standards, Preparation, Sspc, Sspc standards

STRUCTURAL PAINTING STANDARD SPECIFICATIONS

2. One bound copy of the Steel Structures Painting Council, surface preparation specification, SSPC SP-1 - Solvent Cleaning. 3. One bound copy of the most current Steel Structures Painting Council Pictorial Standards, SSPC-VIS 1, Guide and Reference photographs for steel surfaces prepared by dry-abrasive blast cleaning. 4. One bound copy of the ...

  Standards, Specification, Preparation, Structure, Council, Structural, Steel, Painting, Sspc, Structural painting standard specifications, Steel structures painting council

Chartek 1709 - AkzoNobel

Nov 20, 2017 · clean to Sa2½ (ISO8501-1:2007) or SSPC-SP10 quality. Galvanised Substrates Ideally, galvanised substrates should be sweep blast cleaned to a standard similar to Sa1 (ISO8501-1:2007) or SSPC-SP16. For reduced surface preparation options, consult International Protective Coatings. Primers

  Standards, Preparation, Sspc

SSPC-SP1 Solvent Cleaning

SSPC-SP3 details the use of power-assisted tools for surface preparation. The preparation method described here is intended to remove the same contaminants from a surface as in SSPC-SP2, and the procedures before and after using this cleaning method are identical to SSPC-SP2. The standard includes using rotary,

  Standards, Preparation, Cleaning, Solvents, Sspc, Sspc sp1 solvent cleaning

Preparation Guide For Painting Steel Surfaces

The standard has been prepared by the Swedish Corrosion Institute in cooperation with the American Society for Testing and Materials, ASTM, and Steel Structures Painting Council, SSPC, USA. In the specifications relating to preparation of surfaces prior to painting, the SSPC and SIS designations correspond as follows: SSPC-Vis 1 SIS 05 59 00

  Standards, Preparation, Structure, Council, Steel, Painting, Sspc, Steel structures painting council

Technical Data Sheet - Jotun

Carbon steel St 2 (ISO 8501-1) or SSPC SP-2 Sa 2½ (ISO 8501-1) or NACE No. 2 / SSPC SP-10 Aluminum The surface shall be hand or machine abraded with non-metallic abrasives or bonded fibre machine or hand abrasive pads to impart a scratch pattern to the surface. Dry abrasive blast cleaning to NACE No. 6 / SSPC-SP 13. Surface preparation

  Preparation, Sspc

TENNESSEE STANDARD - TN.gov

Jan 01, 2021 · STANDARD SPECIFICATIONS FOR ROAD AND BRIDGE CONSTRUCTION Tennessee Department of Transportation, Authorization No. 401093, 5,000 copies, January 2021. This public document was promulgated at a cost of $5.83 per copy. January 1, 2021

  Standards, Tennessee, Tennessee standards