Handson Technology

3-Axis CNC/Stepper Motor Shield for Arduino The Arduino CNC Shield makes it easy to get your CNC projects up and running in a few hours. It uses opensource firmware on Arduino to control 4 stepper motors using 4 pieces of A4988 Stepper Motor driver breakout board, with this shield and ArduinoUno/Mega, you can build all kinds of robotics, linear ...

  Shield, Motor, Stepper, Stepper motor, Cnc shield

I2C Serial Interface 20x4 LCD Module - HandsOn Tec

I2C Serial Interface 20x4 LCD Module This is I2C interface 20x4 LCD display module, a new high-quality 4 line 20 character LCD module with on-board contrast control adjustment, backlight and I2C communication interface. For Arduino beginners, no more cumbersome and complex LCD driver circuit connection.

  Serial, Interface, Module, 20x4, I2c serial interface 20x4 lcd module

L293D Quadruple H-Bridge Motor Shield For Arduino

Try soldering a ceramic or disc 0.1uF capacitor between the motor tabs (on the motor itself!) this ... This problem can be solved by soldering 3 noise suppression capacitors to the motor. 1 …

  Ceramic, Capacitors, Disc

Handson Technology - Open Source Electronics …

4 www.handsontec.com The most basic way to use the ESP8266 module is to use serial commands, as the chip is basically a WiFi/Serial transceiver. However, this …

Immobilizer and RKE System Design - HandsOn Tech

Immo-RKE-System-Design Version 4 Philips Semiconductors Part 1: Immobilizer Design Content 1 Introduction 2 Immobilizer antenna design 3 …

  System, Design, Immobilizer, Immobilizer and rke system design

Handson Technology

User Guide BTS7960 High Current 43A H-Bridge Motor Driver The BTS7960 is a fully integrated high current H bridge module for motor drive applications. Interfacing to a microcontroller is made easy by the integrated driver IC which features logic level inputs, diagnosis with

  Guide, User, User guide

RC522 RFID Development Kit - HandsOn Tec

4 www.handsontec.com Put the RFID card or the keychain to the reader. Let the reader and the tag closer until all the information is displayed. This is the information that you can read from the card, including the card UID that is highlighted in red.

  Development, Rfid, Rc522 rfid development kit, Rc522

Arduino Due - Farnell element14

Arduino Due Arduino Due Front Arduino Due Back Overview The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU

  Arduino, Arduino due, Arduino due arduino due, The arduino due

The Arduino Mega 2560 is a microcontroller board …

The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 14 can be used as PWM outputs),

  Arduino, Board, Games, Microcontrollers, 6520, The arduino mega 2560 is a microcontroller board

Scratch for Arduino Protocol Specification - S4A

Scratch for Arduino Protocol Specification Actuators messages (Data from Scratch to Arduino) S4A Name Motor 4 Analog 5 Analog 6 Motor 7 Motor 8 Analog 9 Digital 10 Digital 11 Motor 12 Digital 13 Type Continuous rotation Servomotor Pseudo

  Arduino, Specification, Protocol, Scratch, Scratch for arduino protocol specification

Using Arduino Boards in Atmel Studio - Micro …

Introduction There are varieties of hardware tools to program Atmel microcontrollers. But if the chips have bootloaders, they can be programmed using serial ports without needing to use any hardware tools.

  Arduino, Using, Board, Metal, Studio, Using arduino boards in atmel studio

Arduino Nano30 2010 - Gravitech

4/12/2010 9:19:36 AM f=0.94 C:\Users\PAN\Documents\eagle\Arduino Nano30_2010\Arduino Nano30_2010.sch (Sheet: 1/1)

  Arduino, 2010, Arduino nano30 2010, Nano30

Arduino Nano3 0 - Gravitech

1 Arduino Nano (V3.0) User Manual Released under the Creative Commons Attribution Share-Alike 2.5 License http://creativecommons.org/licenses/by-sa/2.5/

  Arduino, Arduino nano3 0, Nano3