PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: dental hygienist

Prescriptive Residential Wood Deck Construction Guide

Copyright 2015 American Wood Council Prescriptive Residential Wood deck Construction Guide Based on the 2012 International Residential Code Where applicable, provisions and details contained in this document are based on the International Residential Code (IRC) [bracketed text references applicable sections of the IRC]. Prescriptive Construction methods recommended meet or exceed minimum requirements of the IRC. Provisions that are not found in the IRC are recommended as good industry practice. Where differences exist between provisions of this document and the IRC, provisions of the IRC shall apply. This document is not intended to preclude the use of other Construction methods or materials.

(Galvannealed) by the Hot-Dip Process, G-185 coating. Hardware to be hot-dipped galvanized after fabrication shall meet ASTM A 123, Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products. Fasteners and connectors exposed to salt …

Fullscreen Download
Loading..

Tags:

  Guide, Construction, Residential, Deck, Woods, Galvannealed, Residential wood deck construction guide

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of Prescriptive Residential Wood Deck Construction Guide

Documents from same domain

INTERIOR SHEAR WALLS - awc.org

www.awc.org

interior shear walls to be designed to resist wind loads. WFCM Section 2.4.4.2 states: “Walls parallel to the applicable wind load or seismic motion shall provide the required shear resistance at each level. The sum of the individual shearwall segment shear

  Walls, Interior

2012 ASD/LRFD Manual for Engineered Wood Construction

www.awc.org

ASD/LRFD MANUAL FOR ENGINEERED WOOD CONSTRUCTION iii AMERICAN WOOD COUNCIL FOREWORD This Allowable Stress Design/Load and Resistance Factor Design Manual for Engineered Wood Construction (ASD/LRFD Manual) provides guidance for design of most wood-based structural products used in the construction

  Construction, Woods, Engineered, Engineered wood construction

2015 National Design Specification Supplement - awc.org

www.awc.org

AMERICAN WD CUNCIL. DESIGN VALUES FOR WOOD CONSTRUCTION – NDS SUPPLEMENT iii. Introduction. This Supplement is a compendium of reference de …

  Supplement

2005 Span Tables For Joists And Rafters - awc.org

www.awc.org

2 EXPLANATION OF TABLES AMERICAN WOOD COUNCIL 7. LUMBER IDENTIFICATION The tabulated spans in these tables apply to lum-ber identified by the grade stamp of, or certificate of

  Table

Design Aid 6 Beam Design Formulas with Shear and Moment ...

www.awc.org

AMERICAN WOOD COUNCIL w R V V 2 2 Shear M max Moment x 7-36 A ab c x R 1 R 2 V 1 V 2 Shear a + — R 1 w M max Moment wb 7-36 B Figure 1 Simple Beam–Uniformly Distributed Load

  Moment

WIND & SEISMIC - AWC

www.awc.org

2.1.2.1 Allowable Stress Design: Allowable stress design (ASD) shall be in accordance with the Na-tional Design Specification ® (NDS ®) for Wood Con-struction (ANSI/AF&PA NDS-05) and provisions of this document. 2.1.2.2 Strength Design: Load and resistance factor design (LRFD) of wood structures shall be in accor-

  Design, Seismic, Load, Wind, Wind amp seismic

WCD1 - Details for Conventional Wood Frame Construction

www.awc.org

may provide equal, or possibly, improved performance. These, however, must provide performance assurance ac-ceptable to the owner and the building inspector. Dimensioning. In general, dimensions for framing lumber, wood sid-ing and trim referenced in this document are nominal dimensions; i.e., 2x4, 2x6, etc., for simplicity. Actual sur-

  Performance, Details

Prescriptive Residential Wood Deck Construction Guide

www.awc.org

3. Maximum allowable overhang cannot exceed L/4 or ¼ of actual main span. Assumes cantilever length/180 deflection with 220 lb point load (See Figure 1A and Figure 2). 4. Incising assumed for Douglas Fir-Larch, Hem-Fir, and Spruce-Pine-Fir. 5. Design values based on northern species with no incising assumed. 6. Ledger shall be a minimum of 2x8 ...

  Guide, Construction, Deck, Maximum, Minimum, Deck construction guide

2015 National Design Specification - AWC

www.awc.org

NDS-1991 with an approval date of October 16, 1992. In 2010, AWC was separately incorporated, re-chartered, and accredited by ANSI as a standards developing organization. The current edition of the Standard is designated ANSI/AWC NDS-2015 with an approval date of September 30, 2014. In developing the provisions of this Specification,

  Design, Specification, 2015, National, October, 2015 national design specification

MAT100: The Basics of Wood Frame Construction

www.awc.org

one comprehensive program for building officials on wood frame construction basics. In each module, learning outcomes will be further refined respectively. MAT 100 learning outcomes (see slide). 5 MAT100: Learning Outcomes 3. Floor, roof/ceiling, wall framing 4. Wall bracing, introduction to Wood Frame Construction Manual 5. Fireblocking ...

  Frame, Slides

Related documents

Zinc-Coated (Galvanized/Galvannealed) Steel Doors and …

steeldoor.org

The galvannealed surface has a non-spangled matte finish with a nominal composition of 90% zinc and 10% iron. This type of coating is referred to with an “A” designation (or “ZF” in SI Units). The galvannealed coating has several advantages compared to the galvanized coating: 1) …

  Doors, Steel, Coated, Zinc, Galvanized, Zinc coated, Galvannealed, Galvanized galvannealed, Steel doors and

GalvInfoNote Understanding Coating Weight Designations …

www.steelmillsoftheworld.com

GalvInfoNote #5 for a full explanation of hot-dip galvannealed coatings. The SI equivalent coating mass designations (ordered as A 653M) for galvannealed sheet are, in g/m2: ZF75 ZF120 ZF180 For galvanized and galvannealed coated sheet, the relationship between coating weight (mass) and thickness is as follows:

  Understanding, Coating, Weight, Designations, Galvannealed, Understanding coating weight designations

Introduction to Steel Doors and Frames

steeldoor.org

Galvannealed steel is still zinc coated – without the spangled look – and is generally coated at A40 or A60. A40 is the minimum recommended weight, while A60 offers better corrosion protection. It is not recommended to go higher than A60 because it reduces paint adhesion. Galvannealed steel is also known

  Galvannealed

AMERICAN NATIONAL STANDARDS INSTITUTE/ STEEL DECK ...

www.sdi.org

Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process b. ASTM A1008 / A1008M - 15, Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable

  Galvannealed

Designation:A 653/A 653M–08 Designation: A 653/A 653M – 09

www.unitedmetalproducts.info

Coated (Galvannealed) by the Hot-Dip Process1 This standard is issued under the fixed designationA653/A653M; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.

  Galvannealed

Cable Tray Systems

www.mphusky.com

fabrication or pre-galvanized steel, zinc plated, galvannealed and fiberglass. 3. Tray Depth A loading depth from 2” to 10” is available, this varies by tray type. 4. Tray Width Standard widths are 6”, 9”, 12”, 18”, 24”, 30” and 36”. (Many other widths …

  Galvannealed

Standard Specification for Steel Sheet, Zinc-Coated ...

www.tjxysteel.com

Coated (Galvannealed) by the Hot-Dip Process1 This standard is issued under the fixed designationA653/A653M; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.

  Standards, Sheet, Steel, Zinc, Specification, Galvannealed, Standard specification for steel sheet

Walkerduct Pro Series - Construction

sweets.construction.com

Duct is made of 16 gauge galvannealed steel with continuous seam weld construction. Makes for easy field cuts and prevents water seepage into the duct. n Large bend radius into duct and around corners and elbows. Maintains integrity of fiber optic cable when changing direction of cable orientation. n Large oblong opening into duct. Allows easy ...

  Galvannealed

Doors and frames - @Republic

www.republicdoor.com

(Galvannealed) by Hot Dipped Process. II. Door Construction A. Doors are either 20 or 18 gauge steel. Door design is a pan and lid construction. The lid has a flattened hemmed edge that is projection welded to the pan. B. Top Channel will be 16 gauge, flush with the top of the door and projection welded on maximum 2 1/2" centers to each face sheet.

  Galvannealed

Introduction Coating Weight [Mass] Measurement Systems

www.scafco.com

galvannealed sheet (zinc-iron alloy-coated) are, in oz/ft2: A25 A40 A60 As with galvanized product designators, A40 for example, requires a minimum average TST coating weight of 0.40 oz/ft2, total both sides. While the coating contains approximately 8 to 10% iron, resulting in

  Galvannealed

Related search queries

Zinc-Coated (Galvanized/Galvannealed) Steel Doors and, Galvannealed, Understanding Coating Weight Designations, Standard Specification for Steel Sheet, Zinc