Process Specification for Installation of Threaded and ...
For threaded fasteners, the effective torque and running torque shall be specified or referenced by the engineering drawing. These torques may be included in the process specification callout note (as above), or they may be located in the field of the drawing in a table or near the appropriate joint, or an assembly
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Process Specification for Passivation and Pickling of ...
mmptdpublic.jsc.nasa.govProhibited descaling prior to passivation. Added Type VII and Type VIII to Table 1 for historical continuity. Combined general passivation and special passivation requirements and section 6.2 and 6.3. Combined general pickling requirements into pickling requirements and renumbered section. Alphabetized and formatted definitions section 10.
Process Specification for Dry-Film Lubricant Application
mmptdpublic.jsc.nasa.govPRC-8001 Rev. E Verify correct version before use. Page 2 of 13 Process Specification for Dry-Film Lubricant Application Prepared by: Signature on file 1/22/13 Daila Gonzalez
Specification, Process, Lubricants, Film, Process specification for dry film lubricant
Process Specification for Liquid Penetrant Inspection
mmptdpublic.jsc.nasa.govAdded requirements for Standard dye penetrant to match with NASA-STD-5009B. 2.0 Applicability – added cracks and pores. 3.2 Added electro-polishing in accordance with PRC-5009. 6.1 General – added Standard Liquid Penetrant inspection, sensitivity Level 3 or 4 fluorescent penetrant shall be used. The “as-
Standards, Specification, Process, Liquid, Inspection, Penetrant, Process specification for liquid penetrant inspection, Standard liquid penetrant
Military Standard Preparation for and Installation of ...
mmptdpublic.jsc.nasa.gov1. This military standard is approved for use by all Departments and Agencies of the Department of Defense. 2. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be …
Installation, Standards, Military, Preparation, Military standard preparation for and installation of
Process Specification for the Resistance Spot Welding of ...
mmptdpublic.jsc.nasa.gova. American Welding Society (AWS) Standards ANSI/AWS A2.4 Standard Symbols for Welding, Brazing and Nondestructive Testing ANSI/AWS A3.0 Standard Welding Terms and Definitions ANSI/AWS D17.2 Specification for Resistance Welding for Aerospace Applications b. NASA/JSC Documents JPG 1700.1 NASA/JSC Requirements Handbook for Safety,
Related documents
A GUIDE TO TORQUE VALUES - Norbar
www.norbar.comthe recommended torque by the appropriate factor shown in the table. Example: bolt and nut are both phosphated; required torque = torque recommended x 0.75. Surface condition of bolt Self Zinc Cadmium Phosphate Self 1.00 1.00 0.80 0.90 Zinc 1.15 1.20 1.35 1.15 Cadmium 0.85 0.90 1.20 1.00 ...
Taper-Lock Bushing Installation and Removal
dpk3n3gg92jwt.cloudfront.netrecommended. Table 1 – Taper–Lock Bushing Bolt Torque Values 8. To increase the bushing gripping force, firmly tap the face of the bushing using a brass drift or punch (Do not hit the bushing directly with the hammer). 9. Re-torque the bushing bolts after Step 8. After reaching the recommended bolt torque value once, stop.
Table, Torque, Bolt, Recommended, Locks, Taper, Taper lock, Bolt torque, Recommended bolt torque
Torque Specifications - Barrington Diesel Club
www.barringtondieselclub.co.zaThe following table has the recommended standard torque values for metric taperlock studs for use Стр. 2 из 5 23.08.2012 12:21 BDC for Manuals - specs - Bolt torques
CROSBY CLIPS WARNINGS AND APPLICATION …
www.thecrosbygroup.comuse torque wrench to retighten nuts to recommended torque. In accordance with good rigging and maintenance practices, the wire rope end termination should be inspected periodically for wear, abuse, and general adequacy. Table 1 Clip Size (in.) Rope Size (in.) Minimum No. of Clips Amount of Rope to Turn Back in Inches * Torque in Ft.Lbs. 1/8 1/8 ...
Applications, Table, Torque, Recommended, Clip, Warnings, Clips warnings and application, Recommended torque
Exhaust Accessories - Donaldson Company
www.donaldson.comRecommended installation torque for any style bent bolt clamp: • For clamps 3" or less - 25 ft. lbs. (34N•M) • For clamps 3" and larger, on tube to tube connections - 35 ft. lbs. (48N•M)
Torque Settings - Grampian Fasteners
www.grampianfasteners.comTorque Settings Suggested Starting Values The below estimated torque calculations are only offered as a guide. Use of its content by anyone is the sole responsibility of that person and they assume all risk. The importance of correct bolt tightening cannot be over emphasized. Determining the correct torque can however present problems.
Gasket - Flexitallic
flexitallic.comMay 15, 2019 · These gaskets can be fabricated in a variety of shapes and sizes recommended for use in high pressure/temperature applications. Except for weld ring gaskets, high loads are required to seat metallic gaskets, as they rely on the deformation or coining of the material into the flange surfaces.
TORQUE-TENSION REFERENCE GUIDE - Fastenal
www.fastenal.comTORQUE-TENSION REFERENCE GUIDE Printed in U.S.A. • Supply Part Number: 9702365 • AS 06/14 Torque Poster For additional technical information, contact Fastenal Engineering at engineer@fastenal.com. Nominal Dia. (in.) Threads per inch 307A ASTM A307 Grade A SAE J429 Grade 5 SAE J429 Grade 8 F N L G 9 FNL Grade 9 Clamp Load (Lbs.) Tightening ...