HIGH MATING FTSH–125–01L–DVEJ CYCLES SMT …

(1.27 mm) .050" FTSH–125–01L–DVEJ FTSH–120–01F–DV FTSH110–01–L–DV m . A Sm . Cm m m Sm Sm m . WWW.SAMTEC.COM For complete specifications and

REVISION CF SSW-1XX-XX-XXX-X-XX-XXX-XX

this document contains confidential and proprietary information and all design, manufacturing, reproduction, use, patent rights and sales rights are expressly reserved by …

  Xx xxx x xx xxx xx

POWER AND VOLTAGE RATING - Samtec …

VOLTAGE and POWER Ratings final 101207.doc 1 OF 13 10/18/2007 D-SCOPE-TECH, INC. POWER AND VOLTAGE RATING SCOPE: The purpose of this document is to take the confusion out of power and voltage ratings in

  Power, Ratings, Voltage, Power and voltage rating, Power ratings

(1.27 mm) .050 FTS SERIES MICRO LOW-PROFILE …

(1.27 mm) .050" FTS SERIES FTS1102L FTS11002FV FTS12201FV FTS11102LVSA Mates with socket strips or IDC cable Impedance matched for high-speed applications

  Series, Profile

REVISION AO FFSD-XX-X-XX.XX-01-X-X-XXX

this document contains confidential and proprietary information and all design, manufacturing, reproduction, use, patent rights and sales rights are expressly reserved by …

  Revisions, Ffsd xx x xx, Ffsd, Xx 01

SFM110–02–L–D–A SFML125–T2–LD–LC …

(1.27 mm) .050" SFML125–T2–LD–LC SFM–125–02–L–SH SFM110–02–L–D–A SFML115–T2–LD–LC Choice of SMT or through-hole tails Locking feature

  Sfm110 02 l d a sfml125 t2 ld lc, Sfm110, Sfml125

HIGH MATING CYCLES THROUGH-HOLE MICRO …

(1.27 mm) .050" FTSH SERIES Im m f applications ( CLP S) sock ips IC le T r surf m (2.51 mm) .0" O (1.27 mm) .050" m FTSH–120–02–L–D FTSH–120–01–L–D–RA

  Ftsh

REVISION J - Samtec Microelectronics

1.95049.53.05001.270.45011.43.0350.89 (typ) cl cl 01 all dimensions are symmetric about the centerline. notes: stencil to be .0060[.152] thick. a k j h

  Dimensions

HIGH MATING CYCLES HTSW115–05–LQ TSW–209–09F–SRA …

tsw, htsw series tsw–112–07–g–t tsw10910–f–d–ra htsw12013–t–d tsw–11416g–sre, , m . a sm . cm m m sm sm m .

HIGH MATING CYCLES LOW-PROFILE DUAL WIPE SOCKET

(1.27 mm) .050" CLP SERIES T Cw contacts CLP–107–02–F–D–P CLP–130–02–L–D CLP–116–02–F–DH CLP–115–02–L–D S m Lw-pro˜le

USB-6210 Specifications - National Instruments

SPECIFICATIONS USB-6210 16 AI (16-Bit, 250 kS/s), 4 DI, 4 DO USB Multifunction I/O Device Definitions Warranted specifications describe the performance of a model under stated operating conditions and are covered by the model warranty. The following characteristic specifications describe values that are relevant to the use of the

  Specification

I/O Wiring and Specifications - AutomationDirect

Specifications 3– 5 I/O Wiring and Specifications In order for an I/O circuit to operate, current must enter at one terminal and exit at another. This means at least two terminals are associated with every I/O point. In the figure to the right, the Input or Output terminal is the main path for the current. One additional terminal must

  Specification, Wiring

TECHNICAL SPECIFICATIONS SERIES 60

Severe-Duty: Less than 6,000 annual miles. Short-Haul: 6,000 to 60,000 annual miles. Long-Haul: Over 60,000 annual miles.

  Specification

ThinkPad X230 Product Specifications Reference (PSREF)

DVI-D via cable 45J7915) • Four USB 2.0 ports • Gigabit ethernet (RJ-45) port • Microphone in and headphone out • Requires 65W or 90W AC adapter • 1.39 lb; 630g An ultraportable for the executive on the move; one spindle Intel Core i5-3210M processor (2 cores, 2.50GHz, 3MB cache), Intel HD Graphics 4000,

  Specification

LOW-PROFILE DUAL WIPE SOCKET 8 - Samtec

Unless otherwise approved in writing by Samtec, all parts and components are designed and built according to Samtec’s specifications which are subject to change without notice. Gbps 8 No. of Positions x (1.27) .050 + (0.43) .017 (3.43).135 A (4.57).180 (4.32).170 (2.29).090 —DH —D

  Specification

PP-D-210089-1 - Solo 3 Home Datasheet

This datasheet details the technical specifications for the Solo 3 ( Home) a variant of the Solo product family. If you’re unsure which model you have, please contact Pod Point directly.

ENGLISH/ METRIC BOLT SUBSTITUTION TABLE

req'd not req'd a - 325 type 1,3 not req’d not req’d m16 m20 m22 m24 m27 m30 m36 5/8 3/4 7/8 1 1 1/8 1 1/4 1 1/2 18 22 24 27 30 34 40 a - 325 type 1 or 3 or a - 449 type 1 a - 325 type 3 a - 354 grade bd or a - 490 types 1 or 3 a - 325 type 1 or 3 or a - 449 type 1 a - 325 type 3 a - 354 grade bd m42 m48 m56 m64 m72 m80 m90