Low-power dual operational amplifier - st.com

February 2016 DocID2471 Rev 17 1/24 This is information on a product in full production. www.st.com LM2904, LM2904A Low-power dual operational amplifier

  Operational, Amplifier, Operational amplifier

AN3128 Application note - st.com

June 2011 Doc ID 16918 Rev 5 1/105 AN3128 Application note STM32 embedded graphic objects/touchscreen library Introduction This library is a firmware package which contains a collection of routines, data structures,

AN4767 Application note - st.com

DocID028380 Rev 2 7/16 AN4767 Dual bank use cases 15 With dual bank, all the manipulation with the other bank is just another task of the main program.

  Applications

AN3155 Application note - st.com

October 2016 DocID17066 Rev 7 1/37 1 AN3155 Application note USART protocol used in the STM32 bootloader Introduction This application note describes the USART protocol used in the STM32 microcontroller

USB Power Delivery and Type-C - st.com

USB Type -C Overview USB Power Delivery specification introduces USB Type-C receptacle, plug and cable; they provide a smaller, thinner and more robust alternative to existing USB interconnect.

Datasheet - L78 - Positive voltage regulator ICs - …

TO- 2 2 0 TO-2 2 0 F P DPAK D² PAK Features • Output current up to 1.5 A • Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18; 24 V • Thermal overload protection

AN2867 Application note - st.com

May 2017 DocID15287 Rev 11 1/43 1 AN2867 Application note Oscillator design guide for STM8AF/AL/S and STM32 microcontrollers Introduction Many designers know oscillators based on Pierce-Gate topology (hereinafter referred to as

  Notes, Applications, Application note

AN4776 Application note - st.com

May 2017 DocID028459 Rev 2 1/73 1 AN4776 Application note General-purpose timer cookbook Introduction The timer peripheral is part of …

  Timer

120-volt, 100-watt, DMOS audio amplifier with mute …

September 2010 Doc ID 6744 Rev 8 1/21 21 TDA7293 120-volt, 100-watt, DMOS audio amplifier with mute and standby Features Multipower BCD technology Very high operating voltage range (±50 V)

Electronic transformer for a 12V halogen lamp - …

APPLICATION NOTE AN528/0999 1/4 ELECTRONIC TRANSFORMER FOR A 12V HALOGEN LAMP by P. Fichera, R. Scollo 1. INTRODUCTION Lighting that uses halogen lamps is commonly found

UTMI+ Low Pin Interface (ULPI) Specification

UTMI+ Low Pin Interface Specification, Revision 1.1 October 20, 2004 Revision History Revision Issue Date Comment 0.9 November 12, 2003 Pre-release. 1.0rc1 January 3, 2004 Introduce PHY interface “modes”. Update interface timings. Clarify 4-bit data clocking. Clarify sending of RX CMD’s and interrupts. Introduce AutoResume feature.

  Specification, Interface, Uitm, Ulpi, Utmi low pin interface

Intel® Chipsets Low Pin Count Interface Specification

Intel may have patents and/or patent applications related to the various Low Pin Count interfaces described in the Low Pin Count (LPC) Interface Specification, Revision 1.1. A reciprocal, royalty-free license to the electrical interfaces and bus protocols described in, and required by, the Low

  Intel, Specification, Count, Interface, Low pin count interface specification, Low pin

Digilent Pmod Interface Specification

The Digilent Pmod interface is used to connect low frequency, low I/O pin count peripheral modules to host controller boards. There are six-pin and twelve-pin versions of the interface defined. The six-pin version provides four digital I/O signal pins, one power pin and one ground pin. The twelve-pin version

  Interface

RS-232 INTERFACE - TSCM

AB 7 SG This line establishes a reference point for all interface voltages. Signal Ground CD 20 DTR This signal line is asserted by the GPIB-232CV to signal that it has been Data Terminal powered on, and is ready to operate. Ready Table 2 . RS-232C Interface Signals. Pin Description Pin Description Pin Description

  Interface, Rs 232 interface

AN2759: Implementing an Ethernet Interface with the ... - NXP

Implementing an Ethernet Interface with the MC9S12NE64, Rev. 0.2 Freescale Semiconductor 5 Figure 4. Pinout of MC9S12NE64 in 80-Pin TQFP-EP Package Designing with the MC9S12NE64 and Adding an Ethernet Interface The MC9S12NE64 is a single-chip Ethernet solution. Having built-in CPU, FLASH, RAM, MAC, and PHY

  Interface

USB to serial chip CH340 - SparkFun Electronics

Data transfer pin contains: TXD pin and RXD pin. When serial interface is idle, RXD must be high-level. If R232 is high-level, use assistant RS232 function, then RXD pin automatically inserts a inverter internal, and low-level is in default. When serial interface output is free, the TXD in CH340H and CH340T is high level, TXD in CH340R is low ...

  Interface

LTC485 – Low Power RS485 Interface Transceiver

Low Power RS485 Interface Transceiver The LTC®485 is a low power differential bus/line trans-ceiver designed for multipoint data transmission standard RS485 applications with extended common mode range (12V to –7V). It also meets the requirements of RS422. The CMOS design offers significant power savings over

  Interface

8-Bit I/O Expander with Serial Interface Data Sheet

Can be confi gured for active-high, active-low or open-drain. VSS 9179 PGround. GP0 10 9 12 I/O Bidirectional I/O pin. Can be enabled for interrupt-on-change and/or internal weak pull-up resistor. GP1 11 10 13 I/O Bidirectional I/O pin. Can be enabled for interrupt-on-change and/or internal weak pull-up resistor. GP2 12 11 14 I/O Bidirectional ...

  Serial, With, Interface, Expanders, O expander with serial interface

MT-019: DAC Interface Fundamentals - Analog Devices

reference using a single package pin. The value of the resistor, R, is typically a few kΩ, thereby allowing the low impedance external reference to override the internal one when connected to the REF OUT/IN pin. Figure 1F shows how the external reference is connected to override the internal reference.

  Devices, Fundamentals, Interface, Analog devices, Analog, Dac interface fundamentals