SURFACE PREP - Thomas Industrial Coatings

Painting a clean surface is imperative for the success of a coating system. There are many di˜erent techniques and procedures used to prepare a surface for application.

  Surfaces

STRUCTURAL PAINTING STANDARD SPECIFICATIONS

specification, SSPC-SP 10 - Near-White Metal Blast Cleaning. 2. One bound copy of the Steel Structures Painting Council, surface preparation specification, SSPC SP-1 - Solvent Cleaning. 3. One bound copy of the most current Steel Structures Painting Council Pictorial Standards, SSPC-VIS 1, Guide and Reference photographs for steel surfaces

  Standards, Specification, Structure, Council, Structural, Steel, Painting, Sspc, Sspc sp, Structural painting standard specifications, Steel structures painting council

Technical Data Sheet

SSPC SP-10 Aluminum The surface shall be hand or machine abraded with non-metallic abrasives or bonded fibre machine or hand abrasive pads to impart a scratch pattern to the surface. Abrasive blast cleaning to achieve a surface profile using non-metallic abrasive media which is suitable to

  Sspc, Sspc sp

PRODUCT DATA SHEET SP-2888 R.G. - Custom Pipe Coating

PRODUCT DATA SHEET SP-2888® R.G. Page 2 of 6 SURFACE PREPARATION: Steel Substrate: Cleanliness: Near White Standards: NACE 2, Sa 2½ (S wedish Scale, ISO 8501-1) SSPC SP-10 (S teel Structures Painting Council) Profile: 62.5 microns minimum to 125 microns maximum (2.5 m ils to 5.0 mils) FBE: Profile: 6.25 microns (2.5 m ils) m inimum

  Product, Sheet, Data, Structure, Council, Painting, Sspc, Tele, Sspc sp, Product data sheet sp, S teel structures painting council

MECHANICAL DESIGN CRITERIA (PROJECT STANDARDS AND ...

- SSPC-PA1 - Shop, Field, and Maintenance Painting - SSPC-PA2 - Measurement of Dry Paint Thickness with Magnetic Gages - SSPC-SPl - Solvent Cleaning - SSPC-SP2 - Hand Tool Cleaning - SSPC-SP3 - Power Tool Cleaning - SSPC-SP6 - Commercial Blast Cleaning - SSPC-SP8 - Pickling - SSPC-SP10 - Near-White Blast Cleaning California Administrative Code ...

  Sspc

REQUIREMENTS FOR PRESERVATION OF SHIP STRUCTURES

Preparation Standard SSPC-SP 14/NACE No. 8, 2007, Industrial Blast Cleaning The Society for Protective Coatings (SSPC) Surface Preparation Specification No.15 (SSPC-SP 15), 2013, Commercial Grade Power Tool Cleaning The Society for Protective Coatings (SSPC) Surface Preparation Specification No. 16 (SSPC-SP

  Sspc, Sspc sp

NACE No. 5/SSPC-SP 12 - iso-iran.ir

NACE No. 5/SSPC-SP 12 NACE International 1 _____ Section 1: General 1.1 This standard describes the use of waterjetting to ach-ieve a defined degree of cleaning of surfaces prior to the application of a protective coating or lining system. These requirements include the end condition of the surface plus ...

  Sspc, Sspc sp

Macropoxy 646 Fast Cure Epoxy 4-53

Immersion: SSPC-SP13/NACE 6-4.3.1 or 4.3.2, or ICRI No. 310.2, CSP 1-3 Surface Preparation Standards Condition of Surface ISO 8501-1 BS7079:A1 Swedish Std. SIS055900 SSPC NACE White Metal Sa 3 Sa 3 SP 5 1 Near White Metal Sa 2.5 Sa 2.5 SP 10 2 Commercial Blast Sa 2 Sa 2 SP 6 3 Brush-Off Blast Sa 1 Sa 1 SP 7 4 Hand Tool Cleaning Rusted C St 2 C ...

  Sspc

DH SYSTEM - DNT

(sspc-sp-10) 調合法 主剤：95部、硬化剤：5部（重量比） 可使時間 10 ℃20 30 40 0 時間16 8 6 塗装方法 刷毛塗り、エアレス塗装、エアスプレー 気温、湿度制限※ 気温：10℃以下、湿度：85rh%以上 使用シンナー ゼッタールEP－2シンナー 塗 装 法

  System, Sspc, Sspc sp, Dh system

SSPC-SP 6/NACE NO. 3 - allweldsandblasting.com

Sep 01, 2000 · SP 1 Solvent Cleaning VIS 1-89 Visual Standard for Abrasive Blast Cleaned Steel 4. Procedures Before Blast Cleaning 4.1 Before blast cleaning, visible deposits of oil, grease, or other contaminants shall be removed in accordance with SSPC-SP 1 or other agreed upon methods. 4.2 Before blast cleaning, surface imperfections such

  Sspc, Sspc sp

مرکز اطلاعات ایزو

Created Date: 5/7/2010 2:32:25 PM