Sspc Sp
Found 12 free book(s)STRUCTURAL PAINTING STANDARD SPECIFICATIONS
www.dot.ny.govspecification, SSPC-SP 10 - Near-White Metal Blast Cleaning. 2. One bound copy of the Steel Structures Painting Council, surface preparation specification, SSPC SP-1 - Solvent Cleaning. 3. One bound copy of the most current Steel Structures Painting Council Pictorial Standards, SSPC-VIS 1, Guide and Reference photographs for steel surfaces
Technical Data Sheet
www.jotun.comSSPC SP-10 Shop primed steel Dry, clean and intact shop primer.Sweep blasted or alternatively blasted to Sa 2 (ISO 8501-1) or SP 6 / NACE No. 3 (SSPC-VIS 1) of at least 70 % of the surface. Coated surfaces Clean, dry and undamaged compatible coating Clean, dry …
Technical Data Sheet
www.jotun.comSSPC SP-10 Aluminum The surface shall be hand or machine abraded with non-metallic abrasives or bonded fibre machine or hand abrasive pads to impart a scratch pattern to the surface. Abrasive blast cleaning to achieve a surface profile using non-metallic abrasive media which is suitable to
PRODUCT DATA SHEET SP-2888 R.G. - Custom Pipe Coating
longhorncustomcoating.comPRODUCT DATA SHEET SP-2888® R.G. Page 2 of 6 SURFACE PREPARATION: Steel Substrate: Cleanliness: Near White Standards: NACE 2, Sa 2½ (S wedish Scale, ISO 8501-1) SSPC SP-10 (S teel Structures Painting Council) Profile: 62.5 microns minimum to 125 microns maximum (2.5 m ils to 5.0 mils) FBE: Profile: 6.25 microns (2.5 m ils) m inimum
MECHANICAL DESIGN CRITERIA (PROJECT STANDARDS AND ...
www.klmtechgroup.com- SSPC-PA1 - Shop, Field, and Maintenance Painting - SSPC-PA2 - Measurement of Dry Paint Thickness with Magnetic Gages - SSPC-SPl - Solvent Cleaning - SSPC-SP2 - Hand Tool Cleaning - SSPC-SP3 - Power Tool Cleaning - SSPC-SP6 - Commercial Blast Cleaning - SSPC-SP8 - Pickling - SSPC-SP10 - Near-White Blast Cleaning California Administrative Code ...
REQUIREMENTS FOR PRESERVATION OF SHIP STRUCTURES
www.dcms.uscg.milPreparation Standard SSPC-SP 14/NACE No. 8, 2007, Industrial Blast Cleaning The Society for Protective Coatings (SSPC) Surface Preparation Specification No.15 (SSPC-SP 15), 2013, Commercial Grade Power Tool Cleaning The Society for Protective Coatings (SSPC) Surface Preparation Specification No. 16 (SSPC-SP
NACE No. 5/SSPC-SP 12 - iso-iran.ir
www.iso-iran.irNACE No. 5/SSPC-SP 12 NACE International 1 _____ Section 1: General 1.1 This standard describes the use of waterjetting to ach-ieve a defined degree of cleaning of surfaces prior to the application of a protective coating or lining system. These requirements include the end condition of the surface plus ...
Macropoxy 646 Fast Cure Epoxy 4-53
p3cdn4static.sharpschool.comImmersion: SSPC-SP13/NACE 6-4.3.1 or 4.3.2, or ICRI No. 310.2, CSP 1-3 Surface Preparation Standards Condition of Surface ISO 8501-1 BS7079:A1 Swedish Std. SIS055900 SSPC NACE White Metal Sa 3 Sa 3 SP 5 1 Near White Metal Sa 2.5 Sa 2.5 SP 10 2 Commercial Blast Sa 2 Sa 2 SP 6 3 Brush-Off Blast Sa 1 Sa 1 SP 7 4 Hand Tool Cleaning Rusted C St 2 C ...
SURFACE PREP - Thomas Industrial Coatings
www.thomasindcoatings.comSSPC-SP10/NACE 2- Near-White Commercial Blast Cleaning This standard conveys the requirements for cleaning a steel surface, painted or unpainted, with the use of abrasive blast media. It also includes instructions for achieving and verifying the standard’s required end condition. As with a commercial blast, the prepared surface must be free ...
DH SYSTEM - DNT
www.dnt.co.jp(sspc-sp-10) 調合法 主剤:95部、硬化剤:5部(重量比) 可使時間 10 ℃20 30 40 0 時間16 8 6 塗装方法 刷毛塗り、エアレス塗装、エアスプレー 気温、湿度制限※ 気温:10℃以下、湿度:85rh%以上 使用シンナー ゼッタールEP-2シンナー 塗 装 法
SSPC-SP 6/NACE NO. 3 - allweldsandblasting.com
allweldsandblasting.comSep 01, 2000 · SP 1 Solvent Cleaning VIS 1-89 Visual Standard for Abrasive Blast Cleaned Steel 4. Procedures Before Blast Cleaning 4.1 Before blast cleaning, visible deposits of oil, grease, or other contaminants shall be removed in accordance with SSPC-SP 1 or other agreed upon methods. 4.2 Before blast cleaning, surface imperfections such
مرکز اطلاعات ایزو
iso-iran.irCreated Date: 5/7/2010 2:32:25 PM