PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: bachelor of science

WIND & SEISMIC - AWC

American Wood CouncilAmericanForest & PaperAssociation2008 EDITIONANSI/AF&PA SDPWS-2008 Approval Date: AuguSt 4, 2008 wind & SEISMICASD/LRFDSpECIAL DESIgN pROvISIONS FOR wind AND SEISMICWITH COMMENTARYU pdates and ErrataWhile every precaution has been taken toensure the accuracy of this document, errorsmay have occurred during or Errata are posted to the American Wood Council website at Technical inquiries may be addressed to American Wood Council (AWC) is the wood products division of the American Forest & PaperAssociation (AF&PA).

wood fiber, manufacturing pulp, paper, and paperboard products from both virgin and recycled fiber, ... Wood fRame ConstRuCtion manual. TAbLE OF cONTENTS. Chapter/Title Page. ... having a density of less than 31 pounds per cubic foot but more than 10 pounds per cubic foot. (LRFD). = = speCial design pRovisions foR Wind and seismiC.

Fullscreen Download
Loading..

Tags:

  Seismic, Brief, Frame, Density, Wind, Wind amp seismic

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of WIND & SEISMIC - AWC

Documents from same domain

MAT100: The Basics of Wood Frame Construction

www.awc.org

one comprehensive program for building officials on wood frame construction basics. In each module, learning outcomes will be further refined respectively. MAT 100 learning outcomes (see slide). 5 MAT100: Learning Outcomes 3. Floor, roof/ceiling, wall framing 4. Wall bracing, introduction to Wood Frame Construction Manual 5. Fireblocking ...

  Frame, Slides

WCD1 - Details for Conventional Wood Frame Construction

www.awc.org

may provide equal, or possibly, improved performance. These, however, must provide performance assurance ac-ceptable to the owner and the building inspector. Dimensioning. In general, dimensions for framing lumber, wood sid-ing and trim referenced in this document are nominal dimensions; i.e., 2x4, 2x6, etc., for simplicity. Actual sur-

  Performance, Details

INTERIOR SHEAR WALLS - awc.org

www.awc.org

interior shear walls to be designed to resist wind loads. WFCM Section 2.4.4.2 states: “Walls parallel to the applicable wind load or seismic motion shall provide the required shear resistance at each level. The sum of the individual shearwall segment shear

  Walls, Interior

2012 ASD/LRFD Manual for Engineered Wood Construction

www.awc.org

ASD/LRFD MANUAL FOR ENGINEERED WOOD CONSTRUCTION iii AMERICAN WOOD COUNCIL FOREWORD This Allowable Stress Design/Load and Resistance Factor Design Manual for Engineered Wood Construction (ASD/LRFD Manual) provides guidance for design of most wood-based structural products used in the construction

  Construction, Woods, Engineered, Engineered wood construction

Prescriptive Residential Wood Deck Construction Guide

www.awc.org

4 PRESCRIPTIVE RESIDENTIAL WOOD DECK CONSTRUCTION GUIDE American Wood Council Table 2. Maximum Joist Spans and Overhangs.1 Species Size Joist Spacing (o.c.)

  Guide, Construction, Woods, Construction guide

2015 National Design Specification Supplement - awc.org

www.awc.org

AMERICAN WD CUNCIL. DESIGN VALUES FOR WOOD CONSTRUCTION – NDS SUPPLEMENT iii. Introduction. This Supplement is a compendium of reference de …

  Supplement

2005 Span Tables For Joists And Rafters - awc.org

www.awc.org

2 EXPLANATION OF TABLES AMERICAN WOOD COUNCIL 7. LUMBER IDENTIFICATION The tabulated spans in these tables apply to lum-ber identified by the grade stamp of, or certificate of

  Table

Design Aid 6 Beam Design Formulas with Shear and Moment ...

www.awc.org

AMERICAN WOOD COUNCIL w R V V 2 2 Shear M max Moment x 7-36 A ab c x R 1 R 2 V 1 V 2 Shear a + — R 1 w M max Moment wb 7-36 B Figure 1 Simple Beam–Uniformly Distributed Load

  Moment

Prescriptive Residential Wood Deck Construction Guide

www.awc.org

3. Maximum allowable overhang cannot exceed L/4 or ¼ of actual main span. Assumes cantilever length/180 deflection with 220 lb point load (See Figure 1A and Figure 2). 4. Incising assumed for Douglas Fir-Larch, Hem-Fir, and Spruce-Pine-Fir. 5. Design values based on northern species with no incising assumed. 6. Ledger shall be a minimum of 2x8 ...

  Guide, Construction, Deck, Maximum, Minimum, Deck construction guide

2015 National Design Specification - AWC

www.awc.org

NDS-1991 with an approval date of October 16, 1992. In 2010, AWC was separately incorporated, re-chartered, and accredited by ANSI as a standards developing organization. The current edition of the Standard is designated ANSI/AWC NDS-2015 with an approval date of September 30, 2014. In developing the provisions of this Specification,

  Design, Specification, 2015, National, October, 2015 national design specification

Related documents

Dell Networking S3100 series

i.dell.com

stacking architecture for high-density aggregation with seamless redundant availability. Hardware, performance and efficiency • Up to 48 line-rate GbE ports of copper or 24 line-rate ports of fiber, two combo ports for fiber/copper flexibility, and two integrated 10GbE SFP+ ports • Up to 48 ports of PoE+ in 1RU without an external power supply

  Dell, Brief, Density, Networking, Dell networking

Related search queries

Dell Networking, Density, Fiber