3 COMPRESSOR MOTOR AND COMPONENT INFORMATION
This motor arrangement uses a start capacitor and a run capacitor in parallel with each other and in series with the motor start winding. This motor has high starting torque, runs efficiently, and is used on many refrigeration and air conditioning applications through 5 HP. A potential relay removes the start
Download 3 COMPRESSOR MOTOR AND COMPONENT INFORMATION
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Refrigeration Manual - HVAC
www.hvacrinfo.com© 1970 Emerson Climate Technologies, Inc. All rights reserved. This is the fifth and last of a series of publications comprising the Emerson Climate Tech-
CONDENSING UNIT CATALOG For more free …
www.hvacrinfo.comVa Value-Ad Con. 2. COPELAND ® BRAND CONDENSING UNIT CATALOG. CONTENTS Page. SystemPro ™ Value-Add Condensing Units 3-4 SystemPro ™ Air-Cooled Condensing Units 5-12
More, Catalog, Unit, Condensing unit catalog for more, Condensing
SECTION D COMPRESSOR NOMENCLATURE - HVAC
www.hvacrinfo.comSECTION D COMPRESSOR NOMENCLATURE TOPICS Welded Compressors .....D2 HFC Welded Compressors .....D4
Section, Compressor, Nomenclature, Section d compressor nomenclature
Copeland Scroll™ Wholesaler Product Guide - HVAC
www.hvacrinfo.comForm No. 2000-46W R1 (10/06) © 2000 Emerson Climate Technologies, Inc. All rights reserved. Copeland Scroll™ Wholesaler Product Guide Also Includes Replacement for Tecumseh and
Guide, Product, Scroll, Copeland scroll wholesaler product guide, Copeland, Wholesaler
Dixell - HVAC
www.hvacrinfo.comDixell Electronic Controls Handbook September 2000 Programming Flow Charts & Parameter Lists for: XR100 Series - Refrigeration Controller XT Series - …
Tecumseh to Tecumseh - HVAC
www.hvacrinfo.comTecumseh to Tecumseh Cross Reference Wholesale Distribution North America. For more free Tecumseh literature please visit. www.HVACRinfo.com
Cross, Reference, Hvac, Cross reference, Tecumseh to tecumseh hvac, Tecumseh, Hvacrinfo
Cross Reference - HVAC
www.hvacrinfo.comCompetitive Cross Reference OEM & Wholesale Distribution North America. For more free Tecumseh literature please visit. www.HVACRinfo.com
Copeland Screw Compressors Semi-Hermetic …
www.hvacrinfo.comCopeland Screw ™ Compressors Semi-Hermetic Compact Application Manual 1 General 2 Design and functions 2.1 Design features 2.2 Compression process Vi control
Applications, Compressor, Screw, Compact, Semi, Hermetic, Copeland, Copeland screw compressors semi hermetic, Copeland screw compressors semi hermetic compact application
rliterature please visit www.HVACRinfo
www.hvacrinfo.comGeneral Information 1-1 Emerson Climate Technologies' Best Practices Guide 2-7 L Series 8-21 Model Nomenclature 8-8 Performance Data 9-18
M and F Line - HVAC
www.hvacrinfo.comM and F Line SystemPro® hermetic air-cooled condensing units Product Information Horsepower: 1/6 – 5 Temperature Applications: Low/Medium/High Refrigerants: R-134a, R-404A, R-22, R-407C
Related documents
AN885, Brushless DC (BLDC) Motor Fundamentals
electrathonoftampabay.orgUnlike a brushed DC motor, the commutation of a BLDC motor is controlled electronically. To rotate the BLDC motor, the stator windings should be energized in a sequence. It is important to know the rotor position in order to understand which winding will be energized following the energizing sequence. Rotor position is
A Textbook of Electrical Technology Vol. 2 - Theraja
www.kurratul.weebly.comPole-pi Winding Element—Coil-span or Coi I-pitch—Pitch of a Winding —Hack Pi Pitch— ... Motor Principle—Comparison of Generator and Motor Ac- lion—Significance of the Bad emf—Voltage EQuation of a Motor—Conditions for Maximum ture …
AC Motor Speed Control - University of Alabama
www.me.ua.eduImportant to match the motor to the load ensure that a change in motor power gives a ... winding Variable Resistor “The traditional way to control the speed of a wound rotor induction motor is to increase the slip by adding resistance in the rotor circuit. ...
Electric Motor Problems & Diagnostic Techniques
www.emerson.cominsulation breakdown which leads to winding failure. They include: 1. Open windings 2. Phase-to-ground 3. Phase-to-phase 4. Turn-to-turn short If the motor keeps running with stator faults, a high current will flow through the windings where the problem is located. This high current generates heat which further degrades winding insulation
Electric, Problem, Technique, Motor, Diagnostics, Winding, Electric motor problems amp diagnostic techniques
CHAPTER 11
pages.mtu.eduThe rotor contains the armature winding, which is the high-power winding of the DC machine. The slots in the lamination provide space for the armature coil. When operating as a generator, the armature winding is rotated through the field, generating a DC voltage that is delivered to the load. For motor operation, the armature winding
IEC STANDARDS FOR VARIABLE SPEED DRIVES AND MOTOR …
irispower.commotor winding. In some circumstances, these surges can be as much as three or four times the rated, rms phase-to-ground voltage, with a risetime as short as 50 ns [5, 8]. These fast risetime surges result in a non-uniform distribution of the impulse voltage across the winding components [7 to 10] with the turns in the first
Brushless DC Motors
engineering.nyu.eduphase stator winding. – Winding as is assumed distributed in slots over the inner circumference of the stator, which is more characteristic of the stator winding than is a concentrated winding. – The winding is depicted as a series of individual coils. Each coil is placed in a slot in the stator steel. – Follow the path of positive current i
ELECTRIC SERVO MOTOR EQUATIONS AND TIME CONSTANTS
support.controltechnologycorp.comFrom the last equation, the motor mechanical time constant, tm, is: tm = e T a T K K R J [sec] (15) The total inertia, JT, is the sum of the reflected inertia to the motor shaft plus the motor inertia. The resistance, Ra, is the motor winding resistance plus the external circuit resistance. Thus the motor mechanical time constant is summarized as: