American - Milgard
AAMA 2410-13 Page 1 1.0 SCOPE . 1.1 This practice covers the installation of retrofit windows in detached one- and two-family dwellings and townhouses not more than three stories above-grade in height with a separate means of egress. 1.2 This practice applies to retrofit windows with an exterior flush fin installed over a pre-existing window frame into a
Download American - Milgard
Information
Domain:
Source:
Link to this page:
Documents from same domain
SLIDING GLASS DOOR ASSEMBLY AND …
www.milgard.comsliding glass door assembly and installation instructions ... before starting the installation ... the outside of the frame by inserting the top and swinging ...
Limited Warranty - Milgard
www.milgard.comcommercial purchaser of its multi-slide doors including, without limitation, stacking, bi-folding and pocket doors (the “Products”): • Workmanship and Materials: each Product shall be free of defects for a period of ten (10) years from the date of
Limited Warranty - Milgard
www.milgard.compurchaser of its multi-slide doors, including without limitation stacking, bi-folding and pocket doors (the “Products”): • Products (two years): each Product shall be free of defects for a period of two (2) years from the date of shipment
Performance Ratings - Milgard
www.milgard.comTuscany® Series Performance Ratings Updated: 8/2014 size bs/vs bs/vs bs/vs Half Vent 6050 -LC-PG-40 0.04 62 01 5 Double Vent 8060 - HS-LC-30 0.03 6 2 0 1 6 8 0 6 0 24 Double Vent 10050 36 HS-LC-25 0.1 6 3 0 3 0 10 0 5 0 36 Double Vent 13060 48 HS-R-15 0.1 6 3 0 1 6 12 13 0 6 0 48 Half Vent Below 6080 36 LC-PG-25 0.05 3.75/6.75 2 0 3 0 6 0 6 0 36 Half Vent Above 6080 36 LC-PG-25 0.03 3.75 2 …
Glass and Glazing - Milgard
www.milgard.comLaminated glass is produced by permanently bonding two pieces of glass together with a tough plastic interlayer (polyvinyl butyral) under heat and pressure. Once bonded together, the sandwich behaves as a single piece. The interlayer is invisible when viewed through the glass and with glass on either side, the finished lite is indistinguishable
Standard Practice for Installation of Windows with a ...
www.milgard.comThis practice addresses the recommended methods and/or sequences used to apply/modify the water-resistive barrier (WRB) or other ... 1.7 This practice is not intended to replace a manufacturer’s installation instructions or federal, state, or local building codes. In all ... and support system, but also on their proper installation. 2.2 ...
Related documents
Surface Treatment of Metals and Plastics
eippcb.jrc.ec.europa.euof other treatments such as painting or photosensitive coatings for printing. Plastics, which are cheaply available and easily moulded or formed, retain their own properties such as insulation ... about 10.5 million tonnes and about 640000 tonnes of architectural components were anodised. Another measure of the industry size and importance is ...
Guide to Stainless Steel Finishes
www.worldstainless.orgdemanding architectural requirements. Four particular surface designations are im-portant for architectural and building appli-cations. These are: 1D, 2D, 2B and 2R. Mill Finishes GUIDE TO STAINLESS STEEL FINISHES 3 1D Hot rolled and annealed, and with the mill scale removed, this surface condition is classified as a 1D finish.
Louver Finishes &Colors Use the reference chart below to ...
content.greenheck.comLouvers and architectural products shall be cleaned, pre-treated and receive a prime coat finish suitable for field painting. Products must be thoroughly cleaned and prepared prior to field application of epoxy, urethane or other heavy-duty coatings. Greenheck does not recommend prime coat or field painting of louvers and architectural products.
Roof and Wall Flashing Architectural Detailing Design Guide
www.stramit.com.auARCHITECTURAL DETAILING This Design Guide has been prepared to assist architects and architectural draftspersons with the design and installation intricacies of detailing roof and wall flashing for metal cladding. Quality of a ... coatings of ZINCALUME ...
SPECIAL INSPECTIONS PROGRAM - 2015 Edition
www.fairfaxcounty.govspecify architectural construction in accordance with the Virginia Construction Code and the Code of the County of Fairfax, and whose signature and seal appear on the county- approved architectural construction documents. Building. Construction with a roof (a "roofed structure”), for use or occupancy. Building core and shell.