ANSI Flanges
ANSI Flanges Tel: 886-4-23112576 Fax: 886-4-23112578 E-mail: wellgrow@ms18.hinet.net WELD NECK THREADED LAP JOINT BLIND SLIP-ON SOCKET WELD
Download ANSI Flanges
Information
Domain:
Source:
Link to this page:
Documents from same domain
Spectifications - Best Pipe Fittings, Steel Fittings ...
www.pipefittingweb.comSpectifications ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers) ANSI / ASME B1.20.1 Pipe Threads, General Purpose (Inch)
Pressure Unit Conversion Table - pipefittingweb.com
www.pipefittingweb.comPressure Unit Conversion Table atm ata ( kg/cm2 ) Torr ( mm Hg) in Hg (32℉) mm water (4℃) in (60℉) bar Mpa Kpa PSI ( lb/in) atm 1 1.033 760 29.92 10332.56 406.79 1.013 0.1013 101.32 14.69 ata ( kg/cm2 ) 0.968 1 735.56 28.96 10000.03 393.71 0.981 0.0981 98.07 14.22
Materials - pipefittingweb.com
www.pipefittingweb.comMaterials Chemical Composition % Mechanical Properties C Mn P S Si Ni Cr Mo N Tensile Strength Yield Strength Elongation HRB Stainless Steel
Concentric and Eccentric Reducers
www.pipefittingweb.comConcentric and Eccentric Reducers MSS SP-75 ANSI B16.9 (in mm) * Wellgrow’s standard. Outside Diameter at Bevel Outside Diameter at Bevel
DIN Flanges - pipefittingweb.com
www.pipefittingweb.comDIN Flanges Summary Chart Rated Pressure (in bar) (1 bar = 14.5 psi = 100 kPa)
Forged High Pressure Pipe Fittings
www.pipefittingweb.comForged High Pressure Pipe Fittings Tel: 886-4-23112576 Fax: 886-4-23112578 E-mail: wellgrow@ms18.hinet.net
90° Long Radius Elbow - pipefittingweb.com
www.pipefittingweb.comLong and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
EN 1092-1 Flanges - pipefittingweb.com
www.pipefittingweb.comFlange type (typ) as in EN 1092-1 01 (Plate [slip-on] flanges for welding) 13 (Hubbed threaded flanges) 02 (Loose plate flanges with weld-on plate collar) 21 (Integral flanges)
Caps - pipefittingweb.com
www.pipefittingweb.comCaps MSS SP-75 ANSI B16.9 (in mm) Nominal Pipe Size (NPS) Outside Diameter at Bevel D Length (2) E Limiting Wall Thickness for Length E Length (3)
Long and Short Radius 45°/ 90° Elbows - …
www.pipefittingweb.comLong and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
Related documents
Standard - ENTECH
www.entech.rsThe resulting 1939 edition contained standards for welding neck flanges (com- pleted in March 1937), 1500 lb flanges in the 14 in. through 24 in. range 2500 lb flanges and flanged fittings in the 1 ⁄
S10 CARBON & STAINLESS STEEL FLANGES • Dimensions & …
atlassteels.com.auClass 150 Flanges to ASME B16.5 CARBON & STAINLESS STEEL FLANGES • Dimensions & Weights BLIND WELDING NECK (WN) SLIP-ON WELDING (SOW) H D A K G H D A K G SOCKET WELDING (SW) H D C A K G B C H D A K G B C SOW, SW Threaded C mm Circle Diam. K mm Hole Diam. H mm Bolts No. Bolt In RF Stud Length mm RF Mach. mm W Neck C …
IS 6392 (1971): Steel pipe flanges
law.resource.orge) Slip-onboss, f) Loose ftanges for welded-onlapped pipe ends, and g) Blank. 1.2 Thisstandarddoes not specify limitations on the use ofvarious methods ofattachment of flanges to pipe or other equipment. The adequacy for operating conditions of any method of attachment specified should be determined by the designer ofthe piping or equipment.
Pipe Flanges and Flanged Fittings
www.abangah-co.comThe resulting 1939 edition contained standards for welding neck flanges (com- pleted in March 1937), 1,500-lb flanges in the 14-in. through 24-in. range, …
ASME B16.5 Flanges
www.hitarm.ruClass 300, Welding Neck, Slip-On and Threaded B16.47, Ser. A ASME B16.5 Flanges Weld Neck, Slip-On, Socket Weld, Threaded, Lap Joint, Blind. 1/2" - 24" Class 150, 300, 400, 600, 900, 1500 and 2500 NOTE: Reducing flanges are available in all types and pressures. To order a reducing flange, state the smaller size first, then the
PIPING PRODUCTS - Prochem
www.prochem.com.auThe most commonly stocked flanges are slip-on, weld neck and blind. (Note that the slip-on flange has a hub similar to the lap joint flange and they should not be misinterpreted). The standard covers sizes up to DN 15 (NPS 1/2") to DN 600 (NPS 24"), in Class ratings of 150, 300, 400, 600, 900, 1500 and 2500. 4.
Flansche ASME Flanges - rff
www.rff.deVorschweißflansche Weld Neck Flanges 36 – 39 Überschiebflansche Slip-on Flanges 41 – 43 Lose Flansche Lap Joint Flanges 44 – 47 Blindflansche Blind Flanges 48 – 51 ... Weld Neck Flanges Class 150 ASME B 165. Class 300 ASME B 165. ½" 21,3 95 15,8 12,7 51 21,3 38 34,9 4 …