Pressure unit Conversion Table atm ata ( kg/cm2 ) Torr ( mm Hg) in Hg (32 F) mm water (4 C) in water (60 F) bar Mpa Kpa PSI ( lb/in) atm 1 760 ata ( kg/cm2 ) 1 Torr ( mm Hg) x10-3 1 in Hg (32 F) 1 mm water (4 C) water (60 F) 1 1 100 Mpa 7500 1 1000 145 Kpa
Pressure Unit Conversion Table atm ata ( kg/cm2 ) Torr ( mm Hg) in Hg (32℉) mm water (4℃) in (60℉) bar Mpa Kpa PSI ( lb/in) atm 1 1.033 760 29.92 10332.56 406.79 1.013 0.1013 101.32 14.69 ata ( kg/cm2 ) 0.968 1 735.56 28.96 10000.03 393.71 0.981 0.0981 98.07 14.22
Domain:
Source:
Link to this page:
1 Pressure unit Conversion Table atm ata ( kg/cm2 ) Torr ( mm Hg) in Hg (32 F) mm water (4 C) in water (60 F) bar Mpa Kpa PSI ( lb/in) atm 1 760 ata ( kg/cm2 ) 1 Torr ( mm Hg) x10-3 1 in Hg (32 F) 1 mm water (4 C) water (60 F) 1 1 100 Mpa 7500 1 1000 145 Kpa 1 PSI ( lb/in) 1
Spectifications ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers) ANSI / ASME B1.20.1 Pipe Threads, General Purpose (Inch)
Materials Chemical Composition % Mechanical Properties C Mn P S Si Ni Cr Mo N Tensile Strength Yield Strength Elongation HRB Stainless Steel
Concentric and Eccentric Reducers MSS SP-75 ANSI B16.9 (in mm) * Wellgrow’s standard. Outside Diameter at Bevel Outside Diameter at Bevel
DIN Flanges Summary Chart Rated Pressure (in bar) (1 bar = 14.5 psi = 100 kPa)
Forged High Pressure Pipe Fittings Tel: 886-4-23112576 Fax: 886-4-23112578 E-mail: wellgrow@ms18.hinet.net
Long and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
Flange type (typ) as in EN 1092-1 01 (Plate [slip-on] flanges for welding) 13 (Hubbed threaded flanges) 02 (Loose plate flanges with weld-on plate collar) 21 (Integral flanges)
Caps MSS SP-75 ANSI B16.9 (in mm) Nominal Pipe Size (NPS) Outside Diameter at Bevel D Length (2) E Limiting Wall Thickness for Length E Length (3)
Long and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
Concentric and Eccentric Reducers MSS SP-75 ANSI B16.9 (in mm) * Wellgrow’s standard. Outside Diameter at Bevel Outside Diameter at Bevel
December 2013 The Leader’s Guide to Unit Training Management (UTM) Unit Training Management (UTM) is the process Army commanders, leaders and staffs use to plan-prepare-execute-assess unit training and identify the resources
Va Value-Ad Con. 2. COPELAND ® BRAND CONDENSING UNIT CATALOG. CONTENTS Page. SystemPro ™ Value-Add Condensing Units 3-4 SystemPro ™ Air-Cooled Condensing Units 5-12
tm 9-2320-362-14&p technical manual operator, unit, direct support and general support maintenance manual including repair parts and special tools list for
Positive: sin, csc Negative: cos, tan, The Unit Circle sec, cot 2Tt 900 Tt 3Tt 2 2700 Positive: sin, cos, tan, sec, csc, cot Negative: none 600
3 TecTronix-GENIUS-BA-CU-EN-3006.doc Installation Do´s and Don´ts Electrical - Do Not cut the connector or the power cables These cables are equipped with special double shields and connectors and must not be cut.
the Seabees as members of our fighting team. SEABEE magazine has represented the officers and men who were the Navy's builders In this war. It has presented their story
Unit 12 Centroids Frame 12-1 Introduction This unit will help you build on what you have just learned about first moments to learn the very important skill of locating centroids.*
Unit 18: Present Perfect Tense vs. Past Tense • 81. Exercise 8: Write the sentences that your teacher reads. Use the words in the box. The number with each word is the sentence number that the word is in.