ANSI Flanges
ANSI Flanges Tel: 886-4-23112576 Fax: 886-4-23112578 E-mail: wellgrow@ms18.hinet.net WELD NECK THREADED LAP JOINT BLIND SLIP-ON SOCKET WELD
Download ANSI Flanges
Information
Domain:
Source:
Link to this page:
Documents from same domain
Spectifications - Best Pipe Fittings, Steel Fittings ...
www.pipefittingweb.comSpectifications ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers) ANSI / ASME B1.20.1 Pipe Threads, General Purpose (Inch)
Pressure Unit Conversion Table - pipefittingweb.com
www.pipefittingweb.comPressure Unit Conversion Table atm ata ( kg/cm2 ) Torr ( mm Hg) in Hg (32℉) mm water (4℃) in (60℉) bar Mpa Kpa PSI ( lb/in) atm 1 1.033 760 29.92 10332.56 406.79 1.013 0.1013 101.32 14.69 ata ( kg/cm2 ) 0.968 1 735.56 28.96 10000.03 393.71 0.981 0.0981 98.07 14.22
Materials - pipefittingweb.com
www.pipefittingweb.comMaterials Chemical Composition % Mechanical Properties C Mn P S Si Ni Cr Mo N Tensile Strength Yield Strength Elongation HRB Stainless Steel
Concentric and Eccentric Reducers
www.pipefittingweb.comConcentric and Eccentric Reducers MSS SP-75 ANSI B16.9 (in mm) * Wellgrow’s standard. Outside Diameter at Bevel Outside Diameter at Bevel
DIN Flanges - pipefittingweb.com
www.pipefittingweb.comDIN Flanges Summary Chart Rated Pressure (in bar) (1 bar = 14.5 psi = 100 kPa)
Forged High Pressure Pipe Fittings
www.pipefittingweb.comForged High Pressure Pipe Fittings Tel: 886-4-23112576 Fax: 886-4-23112578 E-mail: wellgrow@ms18.hinet.net
90° Long Radius Elbow - pipefittingweb.com
www.pipefittingweb.comLong and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
EN 1092-1 Flanges - pipefittingweb.com
www.pipefittingweb.comFlange type (typ) as in EN 1092-1 01 (Plate [slip-on] flanges for welding) 13 (Hubbed threaded flanges) 02 (Loose plate flanges with weld-on plate collar) 21 (Integral flanges)
Caps - pipefittingweb.com
www.pipefittingweb.comCaps MSS SP-75 ANSI B16.9 (in mm) Nominal Pipe Size (NPS) Outside Diameter at Bevel D Length (2) E Limiting Wall Thickness for Length E Length (3)
Long and Short Radius 45°/ 90° Elbows - …
www.pipefittingweb.comLong and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
Related documents
Steel– AISC Load and Resistance ... - Texas A&M University
faculty-legacy.arch.tamu.edu1. The contribution of the flanges to shear capacity may be neglected. 2. y w F h t ≤418 where h equals the clear distance between flanges less the fillet or corner radius for rolled shapes. With these assumptions, the calculated strength becomes simple. Neglecting the flanges, all
Carbon Steel Pipe, Fittings and Flanges - Atlas Steels
atlassteels.com.auSection 5 – Carbon Steel Pipe Fittings and Flanges Carbon Steel Pipe Fittings and Flanges October 2016 Page 3 – Section 5 www.atlassteels.com.au Specifications – Carbon Steel Pipe, Buttwelding Fittings & Flanges Linepipe Specification ASTM A53/A53M Dimensions ASME B36.10M Product Welded and Seamless Steel Pipe Grades A, B
Structural Steel Sections (Eurocode 3, EN1993-1-1 ... - Runet
runet-software.comDesign tables for Structural Steel Sections (Eurocode 3, EN1993-1-1:2005) Tables with all the international steel sections, with their dimensions, properties, classification, resistance and buckling resistance values according to Eurocode 3, EN1993-1-1:2005. The tables are extended to welded section with dimensions given from the user. z. z
COMPANION TO THE AISC STEEL CONSTRUCTION MANUAL
www.aisc.org1. The 2016 AISC Specification for Structural Steel Buildings is referred to as the AISC Specification and the 15th Edition AISC Steel Construction Manual, is referred to as the AISC Manual. 2. The 2016 ASCE Minimum Design Loads and Associated Criteria for Buildings and Other Structures is referred to as ASCE/SEI 7. 3.
Flanges and Fittings ISO-KF, ISO-K ... - Leybold Online Shop
www.leyboldproducts.comFlanges and Fittings ISO-KF, ISO-K, ISO-F, CF 280.00.02 Excerpt from the Oerlikon Leybold Vacuum Full Line Catalog 2015/2016 Catalog Part Flanges and Fittings. ... other nickel chromium steel grades - For use either with a flat gasket made of OFHC copper (oxygen-free) or FPM (FKM) O-ring - Self-centering - Fixed and rotary flanges in almost
Stainless Steel Flanges - Paramount Supply
www.paramountsupply.com150# Stainless Steel Flange Dimensions, cont. Nominal Size Min Thread Length (T) Depth of Socket (D) Diameter Hub at Bevel (A) Hub Diameter (X) Drilling Approximate Weight Bolt Circle Diameter Holes Number of Holes Weld Neck Sip-on Threaded & Socket Weld Lap Joint Blind 1/2 0.62 0.38 0.84 1.19 2.38 0.62 4 2 1 1 1 3/4 0.62 0.44 1.05 1.50 2.75 0 ...
23 22 13 Steam and Steam ... - University of Houston
www.uh.edua. Fittings: Carbon steel, ASTM A234 WPB, seamless welding fittings, standard weight for steam, Schedule 80 for condensate. b. Joints: Butt weld. c. Flanges: 300 lb., ANSI forged carbon steel, ASTM A181 Class 70, weld neck raised face. d. Gaskets: Flexitallic Style CG, API 601 spiral wound 304SS with Grafoil Fill or accepted substitution. e.