Arduino : Introduction & Programming
disk controllers and serial/parallel port functions. These backplane-based microcomputers were used for data acquisition, process control and R&D projects, but were generally too bulky to be used as embedded systems within devices.
Download Arduino : Introduction & Programming
Information
Domain:
Source:
Link to this page:
Documents from same domain
UART - Students' Gymkhana, IIT Kanpur
students.iitk.ac.inUART: Universal Asynchronous Receiver Transmitter UART is a simple half-duplex, asynchronous, serial protocol. Simple communication between two equivalent nodes. Any node can initiate communication. Since connection is half-duplex, the two lanes of communication are completely independent.
Project Documentation - IIT Kanpur
students.iitk.ac.inPROJECT DOCUMENTATION Project Title - Geotagging. Team Members - Enayat Ullah, Ishaan Kumar, Vishal, Anshul Goyal. Motivation We approached the club with a lot of ideas, some our own, some plagiarised from
KEYBOARD INTERFACE WITH MICROCONTROLLER
students.iitk.ac.inKEYBOARD INTERFACE WITH MICROCONTROLLER Most microcontrollers require some kind of a human interface. This tutorial describes one way of doing this
SENSORS & ACTUATORS
students.iitk.ac.in4. Infrared Sensor IR led is led that emits light in IR region and can't be seen by the eyes. Photodiode is a type of diode which works in reverse bias and its resistance is changed when subjected to change in light intensity. They are used for colour detection etc.
GLIDER BASICS - IIT Kanpur
students.iitk.ac.inWING The point in airfoil where the lift can be supposed to be concentrated upon is called the centre of pressure. Generally it is located at c/4, where c is the chord length. The point where the weight of the glider acts is termed as centre of gravity (CG). For weight balance, the centre of gravity must coincide with the centre of pressure.
Verilog Fundamentals - IIT Kanpur
students.iitk.ac.inOPERATORS AND CONDITIONAL OPERATORS All the arithmetic as well as logical operators in Verilog are similar to C, except ++ and -- which are not available in Verilog. Conditional statements are also similar to C with following modifications: • { is replaced by begin. • } is replaced by end.
Related documents
USB to I2C Example using the FT232H and FT201X devices
www.ftdichip.com2 FT232H USB-I2C Master This section shows how the FT232H can be programmed to act as a USB to I2C master interface. These routines can be used as the basis for communicating with other I2C slave devices. The routines will be used in the following chapter to communicate 2with the FT201X I C slave as an example.
CP2104 - Silicon Labs
www.silabs.comRS-232/RS-485 designs to USB using a minimum of components and PCB space. The CP2104 includes a USB 2.0 full-speed function controller, USB transceiver, oscillator, one-time programmable ROM, and asynchronous serial data bus (UART) with full modem control signals in a compact 4x4mm QFN-24 package (sometimes called “MLF” or “MLP”).
USB to serial chip CH340 - SparkFun Electronics
cdn.sparkfun.comCH340 is a USB bus convert chip and it can realize USB convert to serial interface, USB convert to IrDA infrared or USB convert to printer interface. In serial interface mode, CH340 supplies common MODEM liaison signal, used to enlarge asynchronous serial interface of computer or upgrade the common serial device to USB bus directly. More
NI Serial Hardware Specifications and Features Guide ...
www.ni.com4 | ni.com | NI Serial Hardware Specifications and Features Guide PXI-8433/2 RS-485/ RS-422 2 Yes 3000.0‡ DB-9 male 128 PXI-8433/4 RS-485/ RS-422 4 Yes 3000.0‡ 10P10C 128 * All NI serial hardware support s standard baud rates.In add ition, the PCI/NI PCIe/PXI-843 x family of
TTL-232R TTL to USB Serial Converter Range of Cables …
www.ftdichip.comThe TTL-232R cables are a family of USB to TTL serial UART converter cables incorporating FTDI’s FT232RQ USB to Serial UART interface IC device which handles all the USB signalling and protocols. The cables provide a fast, simple way to connect devices with a TTL level serial interface to USB.
UM2448 User manual - STMicroelectronics
www.st.com– 3 V to 3.6 V application voltage support on the UART interface and 5 V tolerant inputs (extended down to 1.65 V with the B-STLINK-VOLT or B-STLINK-ISOL board) – VCP frequency up to 16 MHz – Available on STDC14 debug connector (not available on MIPI10) • Multi-path bridge USB to SPI/UART/I2C/CAN/GPIOs specific features:
Raspberry Pi Compute Module 3+ Raspberry Pi Compute …
datasheets.raspberrypi.comUSB Interface USB Dx I/O - Z Leave open Serial interface USB OTGID I 3V3 Tie to GND OTG pin detect HDMI Interface HDMI SCL I/O 3V3b Zf Leave open DDC Clock (5.5V tolerant) HDMI SDA I/O 3V3b Zf Leave open DDC Data (5.5V tolerant) HDMI CEC I/O 3V3 Z Leave open CEC (has internal 27k pull up) HDMI CLKx O - Z Leave open HDMI serial clock
HC-05 Bluetooth Module - GM e
www.gme.czTXD UART_TXD, Bluetooth serial signal sending PIN Connect with the MCU’s (Microcontroller and etc) RXD PIN. RXD UART_RXD, Bluetooth serial signal receiving PIN Connect with the MCU’s (Microcontroller and etc) TXD PIN. KEY Mode switch input If it is input low level or connect to the air, the module is at paired or communication mode.