BGM220P Wireless Gecko Bluetooth Module Data Sheet
to Design Guidelines for recommendations to achieve optimal an-tenna performance. Peak gain 1.86 dBi 3.4 Power Supply The BGM220P requires a single nominal supply level of 3.0 V to operate. All necessary decoupling and filtering components are inclu-ded in the module. BGM220P Wireless Gecko Bluetooth Module Data Sheet System Overview
Download BGM220P Wireless Gecko Bluetooth Module Data Sheet
Information
Domain:
Source:
Link to this page:
Documents from same domain
Frequency Modulation FM Tutorial - Silicon Labs
www.silabs.comFrequency Modulation (FM) Tutorial Lawrence Der, Ph.D. Silicon Laboratories Inc. Introduction Edwin H. Armstrong, known as one of the founding fathers of radio technology, invented the
AN986: BLUETOOTH® A2DP AND AVRCP PROFILES
www.silabs.comSilicon Labs TABLE OF CONTENTS 1 Introduction 4 1.1 Advanced Audio Distribution Profile 4 1.2 Audio/video Remote Control Profile 5 2 iWRAP firmware overview 6
C8051F310/1/2/3/4/5/6/7 - Silicon Labs
www.silabs.comC8051F310/1/2/3/4/5/6/7 Rev. 1.8 3 Table Of Contents 1. System Overview..... 17
Isolated RS232 and RS485 Expansion Board User Guide
www.silabs.comIsolated RS232 and RS485 Expansion Board User Guide The Silicon Labs Isolated RS232 and RS485 Evaluation Board is a hardware plugin card for EFM8 and EFM32 Starter Kits (STKs).
C8051F040/1/2/3/4/5/6/7 - Silicon Labs
www.silabs.comC8051F040/1/2/3/4/5/6/7 Rev. 1.6 3 Table of Contents 1. System Overview..... 19
A Stroke of Genius for Smart TVs: Add Voice to Your Remote ...
www.silabs.comA Stroke of Genius for Smart TVs: Add Voice to Your Remote Control Introduction In this age of the Internet of Things (IoT), connected devices are getting smarter and smarter. We have smart phones, smart homes, smart cars, smart appliances, and even ... digitize our voice and send it over the Internet where it is processed for a response. The
DESIGN OF PRINTED TRACE DIFFERENTIAL OOP NTENNAS 1 ...
www.silabs.comalso provides a general tutorial on how to design a differential loop antenna, using a combination of design ... 2.1. Design Characteristics of Loop Antennas The following represents a brief list of some of the characteristics of loop antennas; each of these items is
High-Performance, Single-Chip …
www.silabs.comThe Si4629 supports worldwide analog AM and FM radio reception and incorporates a fully integrated decoder for the European Radio Data System (RDS) and the North
AN1107: Si5332 Power Supply Noise Rejection - Silicon Labs
www.silabs.comAN1107: Si5332 Power Supply Noise Rejection This application note showcases the power supply noise rejection (PSNR) performance of Si5332. Power supply noise are a significant problem in high performance clocking. A clock cir-cuit that is dependent on a voltage source will be affected by the noise of that source in the following ways:
Enhancing Power Supply Rejection Ratio for Low-Jitter Clocks
www.silabs.comEnhancing Power Supply Rejection Ratio for Low-Jitter Clocks . Today's electronic systems require advanced design from top to bottom. Cost and ... especially in high-power systems. Ripple as high as 100 mVp-p is common in some networking and computing applications.
Related documents
Micropower, 3-Axis, ±2 g/±4 g/±8 g Digital Output MEMS ...
www.analog.comrange. For applications where a noise level lower than the normal 550 µ g /√Hz of the ADXL362 is desired, either of two lower noise modes (down to 175 µ g /√Hz typical) can be selected at minimal increase in supply current. In addition to its ultralow power consumption, the . ADXL362. has many features to enable true system level power ...
We Take the Hard Out of HARDFACING - Lincoln Electric
www.lincolnelectric.comWear from gritty material accompanied by heavy pounding which tends to chip or crack, as well as grind, away the surface. Severe Abrasion Wear from gritty materials which grind or erode the surface. Severe abrasion is often accompanied by heavy …
MAY 1999 JOINT INDUSTRY STANDARD
www.navsea.navy.mile.g., hand-soldering, hot bar attach of gull wing leads, and pin-thru-hole with backside wave solder. The heat absorbed by the package body from such operations is typically much lower than for bulk surface mount reflow or hot air rework, and moisture precautionary measures are typically not needed. 3.3 Reliability
I 2 Features and benefits MPL3115A2
www.nxp.com8.2 Board mount recommendations Components can be mounted using solder paste stencil, screen printed or dispensed onto the PCB pads prior to placement of the component. The volume of solder paste applied to the PCB is normally sufficient to secure the component during transport to the subsequent reflow soldering process.
LMx24-N, LM2902-N Low-Power, Quad-Operational …
www.ti.comSOIC Package 800 800 mW Output Short-Circuit to GND (One Amplifier)(5) V + ≤15 V and TA = 25°C Continuous Continuous Lead Temperature (Soldering, 10 seconds) 260 260 °C Soldering Information Dual-In-Line Package Soldering (10 seconds) 260 260 °C Small Outline Package Vapor Phase (60 seconds) 215 215 °C Infrared (15 seconds) 220 220 °C
LM555 Timer datasheet (Rev. D)
www.ti.comLM555 www.ti.com SNAS548D –FEBRUARY 2000–REVISED JANUARY 2015 6.5 Electrical Characteristics (TA = 25°C, VCC = 5 V to 15 V, unless otherwise specified)(1)(2) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Supply Voltage 4.5 16 V Supply Current VCC = 5 V, RL = ∞ 3 6 V mA CC = 15 V, RL = ∞ 10 15 (Low State) (3) Timing Error, Monostable