Bitumastic 300M - Carboline
* Disclaimer: Bitumastic 300M is a proprietary formula that is not necessarily formulated to the exact compositional guidelines set forth in some of these standards. Major deviations that control and improve application characteristics may be present, but does not have a detrimental effect on the suitability for use outlined ...
Download Bitumastic 300M - Carboline
Information
Domain:
Source:
Link to this page:
Documents from same domain
Carbomastic 15 - Carboline
msds.carboline.comGeneric Type Epoxy Mastic Description Aluminium-pigmented, low-stress, high solids mastic with a proven field history. Carbomastic 15 was the pioneer mastic coating in a number of industrial markets and today still provides unmatched levels of barrier protection and corrosion resistance over existing finishes and rusted or
Carbozinc 859 - Carboline
msds.carboline.comGeneric Type Organic Zinc Rich Epoxy Description Low VOC organic zinc epoxy steel primer with extremely fast cure-to-topcoat characteristics for in-shop applications and quick turnaround requirements in the field. Carbozinc 859 has less than 360g/litre VOC (thinned) and is used extensively in virtually all industrial markets. Features
Carbozinc 11 HS - Carboline
msds.carboline.comThese are nominal values. When used as a pre-construction primer thin up to 38 oz/gal using exempt Thinner 236 E. Topcoats Acrylics, Epoxies, Polyurethanes, High Heat Silicones, Silicates and others as recommended by your Carboline sales representative. Not required for certain exposures. A mist-coat/full-coat spray technique is often required to
Carboguard 893 - Carboline
msds.carboline.comBrush Use a medium bristle brush. Roller Use a short-nap synthetic roller cover with phenolic core. APPLICATION CONDITIONS Condition Material Surface Ambient Humidity Minimum 4°C (40°F) 4°C (40°F) 4°C (40°F) 0% Maximum 32°C (90°F) 57°C (135°F) 43°C (110°F) 90% This product simply requires the substrate temperature to be above the ...
Carbothane 134 HG - Carboline
msds.carboline.com24°C (75°F) 8 Hours 8 Hours 7 Days 32°C (90°F) 4 Hours 4 Hours 5 Days These times are based on a 50 micron dry film thickness. Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure. *Maximum self-recoat times are indefinite.
Carbothane 134 - Carboline
msds.carboline.comNOTE: Substitute thinners, especially Lacquer Thinners, may contain alcohols which will inhibit the cure of Carbothane 134. Use of thinners other than those supplied or approved by StonCor Africa may adversely affect product performance and void product warranty, whether express or implied. Ratio 8:1 Pot Life
Thermaline 450 EP - Carboline
msds.carboline.comSurface profile should be a dense angular 1-3 mils and is best achieved through abrasive blasting. Remove all contaminants that would interfere with the performance of stainless steel for the intended service such as, but not limited to, imbedded iron or chlorides.
Carboguard 890 - Carboline
msds.carboline.comJanuary 2019 890 Page 2 of 4 SUBSTRATES & SURFACE PREPARATION General Surface must be clean and dry. Remove all dirt, dust, oil and all other contaminants. Steel Immersion: ISO 8501 Sa2½ Non-immersion: ISO 8501 Sa2½ 40 to 75µm ISO 8501 St2 or St3 are suitable cleaning methods for mild environments. Galvanized Steel
SELECTION & SPECIFICATION DATA - Carboline
msds.carboline.comto these guidelines to achieve the desired results. Spray Application (General) The following spray equipment has been found suitable and is available from equipment manufacturers. Keep material under mild agitation during application. If spraying stops for more than 10 minutes, recirculate the material remaining in the spray line.
Carboguard 635 - Carboline
msds.carboline.comPotable Water Use: (0200) Beige, (0700) Grey and (0800) White Other Colours: Red and Black Gloss Satin Primer Self-priming Recommended Thickness 100 to 150 microns per coat Solid(s) Content By Volume: 65% ± 2% Theoretical Coverage Rates 25.6m²/litre at 25 microns 6.4m²/litre at 100 microns 4.3m²/litre at 150 microns Allow for loss in mixing ...