Concentric Vent Installation Guide - DiversiTech
a) The DiversiTech concentric vent termination kit is intended for use with Category IV high efficiency (condensing gas) furnaces or water heaters with exhaust temperatures up to and including 65°C (149°F), ULC S636 Class II. Failure to follow this warning could result in fire, personal injury or death.
Download Concentric Vent Installation Guide - DiversiTech
Information
Domain:
Source:
Link to this page:
Documents from same domain
CARBON MONOXIDE DETECTOR REQUIREMENTS …
media.diversitech.comcarbon monoxide detector requirements by state ... ark. code ann. § 4-86-109 ... carbon monoxide detector requirements by state
MATERIAL SAFETY DATA SHEET - DiversiTech
media.diversitech.comMaterial Safety Data Sheet Page 1 of 6 Section 1: Product & Company Identification Product Name: Zinc-It® Instant Cold Galvanize Product Number (s): 18412, 18412-6
Pro-Blue - DiversiTech
media.diversitech.comSAFETY DATA SHEET DiversiTech Corporation Chemical Emergency: P 800-255-3924 Pro-Blue™
TECHNICAL DATA SHEET - DiversiTech
media.diversitech.comDOC32214 www.diversitech.com 1.800.995.2222 TECHNICAL DATA SHEET Product Purpose Features CVENT-2 2” 34 3/4“ 3 1/2” 19 1/2“
Pro-GreenTM - DiversiTech
media.diversitech.comSAFETY DATA SHEET DiversiTech Corporation Chemical Emergency: P 800-255-3924 6650 Sugarloaf Parkway P 678.542.3600 Duluth, GA 30097 Page 1 of 5 F 678.542.3700
Vent termination Kits - DiversiTech
media.diversitech.comVent termination Kits All Fittings included DiversiTech’s CVENT series concentric vent kit includes all fittings a contractor will need to install the vent.
INSTALLATION ol.indd 1 2/1/05 4:19:25 PM - DiversiTech
media.diversitech.comThe contacts of the Wet Switch’s relay may be wired to use multiple Wet Switches. The drawing to the right shows the contacts 6650 Sugarloaf Parkway interrupting the 24 VAC signal when either Wet Switch gets wet. Duluth, GA USA 800.995.2222 678.542.3700 FAX www.diversitech.com SPECIFICATIONS:
Igniter Cross Reference - DiversiTech
media.diversitech.comigniter cross reference ign-001 ign-001 company o.e.m. or distributor part# ign-1f 700-3 ign-1r 700-4 ign-2 700-5 780-001 universal silicon
Related documents
Service Literature G26 SERIES UNITS
www.completeheating.caConcentric Vent/Intake Air/Roof Termination Kit (optional) 60G77 1 1/2 inch (38 mm) Vent/Intake Air Roof 2 inch (51 mm) 15F75 Vent/Intake Air Roof Termination Kit (optional) vent size 3 inch (76 mm) 44J41 Vent/Intake Air Wall Termination Kit (optional) vent size 2 inch (51 mm) 15F74 (ring kit) 22G44 (close couple) 30G28 (WTK close couple)
UBBINK™ VENT SYSTEM FOR RINNAI TANKLESS WATER …
documents.alpinehomeair.com24 224046 Raised Horizontal Termination Kit (“Snorkel”) (94LSi, R75LSi, R50LSi) VENT PIPE EXTENSIONS 7 224051 224260 10” Vent Pipe Extension 224052 224265 19.5” Vent Pipe Extension 224053 224270 39” Vent Pipe Extension 8 224054 224275 Telescoping Vent Length 9 224063 224255 90 Degree Elbow
FLUE GAS VENTING SYSTEMS
www.ipexna.com• Concentric Vent Kits can be field modified, providing compliance with BOTH the appliance manufacturers’ and IPEX’s guidelines ACCESSORIES WALL TERMINATION KITS For a traditional vent style, IPEX’s PVC Wall Termination Vent Kits are available in convenient 2”, 2-1/2” and 3” sizes. These PVC kits require only two
Installation & Operation Manual Models: 80 - 285 Starting ...
www.lochinvar.comInstallation & Operation Manual Models: 80 - 285 Starting Serial #H07H10040039 This manual must only be used by a qualified heating installer / service
VENTING OF CATEGORY IV APPLIANCES (HIGH-EFFICIENCY …
www.rses.orga concentric fitting (see Figure 1). It allows the vent pipe and the air intake to exit the building through one penetration. The fitting is actually a double-wall ... The proper termination of the vent piping is important to consider before starting any venting job. Category IV …
Direct Exhaust Venting Kit Instructions - Weil-McLain
www.weil-mclain.comMaximum vent lengths apply for either 3” or 4” vent and air pipe. If using 3” pipe, provide 4”x 3” tapered reducers at boiler connections and at Weil-McLain vent/air cap termination. Boilers will derate as vent length increases — see rating data on Figure 123, page 129 in the boiler manual for derate amounts. SIDEWALL termination
Z-VENT Special Gas Vent System
www.z-flex.comZ-VENT® aae e a ae a Z-VENT® Special Gas Vent Page 6 Z-Quote™ is a revolutionary software solution that creates a detailed, dimensional, Z-VENT® system layout, accurate bill of material and quote proposal in minutes. Simply submit a completed design check list and our technical staff will provide you with a quote, detailed drawing with part call outs, and material list.