VENTING OF CATEGORY IV APPLIANCES (HIGH-EFFICIENCY …
a concentric fitting (see Figure 1). It allows the vent pipe and the air intake to exit the building through one penetration. The fitting is actually a double-wall ... The proper termination of the vent piping is important to consider before starting any venting job. Category IV …
Tags:
Termination, Vents, Concentric
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
PNEUMATIC CONTROLS – PREVENTIVE …
www.rses.orgService Application Manual SAM Chapter 620-83 Section 7B PNEUMATIC CONTROLS – PREVENTIVE MAINTENANCE AND TROUBLESHOOTING Johnson Controls, Inc.
Control, Troubleshooting, Maintenance, Preventive, Pneumatic, Pneumatic controls preventive, Pneumatic controls preventive maintenance and troubleshooting
THE PSYCHROMETRIC CHART AND ITS USE - …
www.rses.orgCopyright © 1959, 2009, By Refrigeration Service Engineers Society.-1- Service Application Manual SAM Chapter 630-16 Section 3A THE PSYCHROMETRIC CHART AND ITS USE
Chart, Chapter, The psychrometric chart and its use, Psychrometric
REFRIGERANT 410A - RSES.org
www.rses.orgINTRODUCTION Recently a new refrigerant, R-410A, has been formu-lated and currently is being used in the HVAC/R industry. It was developed primarily because the pro-
REFRIGERANT 410A - RSES.org
www.rses.orgINTRODUCTION Recently a new refrigerant, R-410A, has been formu-lated and currently is being used in the HVAC/R industry. It was developed primarily because the pro-
TERMINAL MARKINGS AND INTERNAL WIRING …
www.rses.orgTERMINAL MARKINGS AND INTERNAL WIRING ... MG 1-2.20 Numerals on Terminals Of Alternating-Current Polyphase ... TERMINAL MARKINGS AND INTERNAL WIRING DIAGRAMS ...
Internal, Current, Marking, Terminal, Wiring, Diagrams, Polyphase, Alternating, Terminal markings and internal wiring, Alternating current polyphase, Terminal markings and internal wiring diagrams
Understanding sUperHeat - RSES.org
www.rses.orgw w w . r s e s j o u r n a l . c o m JUNE 2010 RSES Journal 15 Image 3 Pressure applied toward a fluid will affect its saturation temper-ature—a factor that can complicate determining superheat.
AN INTRODUCTION TO Static Pressure - RSES.org
www.rses.org14 RSES Journal NOVEMBER 2014 www.rsesjournal.com You can compare the actual coil pressure drop to the man-ufacturer’s rated coil pressure drop at the rated air flow to
REFRIGERANT PIPING INTRODUCTION - RSES.org
www.rses.orgCopyright © 1964, 2009, By Refrigeration Service Engineers Society.-2- DISCHARGE OR HOT GAS LINES The discharge or hot gas piping is …
Services, Introduction, Engineer, Refrigerant, Society, Piping, Refrigeration, Ress, Refrigerant piping introduction, Refrigeration service engineers society
OPERATION OF AMMONIA REFRIGERATION …
www.rses.orgService Application Manual SAM Chapter 620-89 Section 1E OPERATION OF AMMONIA REFRIGERATION SYSTEMS International Institute of Ammonia Refrigeration
Operations, System, Refrigeration, Ammonia, Operation of ammonia refrigeration, Operation of ammonia refrigeration systems
OIL IN REFRIGERATION SYSTEMS - RSES.org
www.rses.orgService Application Manual SAM Chapter 620-107 Section 1A OIL IN REFRIGERATION SYSTEMS INTRODUCTION Until the phaseout of CFC refrigerants, mineral oils were the primary oils used in refrigeration systems.
Introduction, System, Refrigeration, Refrigeration systems, Refrigeration systems introduction
Related documents
Service Literature G26 SERIES UNITS
www.completeheating.caConcentric Vent/Intake Air/Roof Termination Kit (optional) 60G77 1 1/2 inch (38 mm) Vent/Intake Air Roof 2 inch (51 mm) 15F75 Vent/Intake Air Roof Termination Kit (optional) vent size 3 inch (76 mm) 44J41 Vent/Intake Air Wall Termination Kit (optional) vent size 2 inch (51 mm) 15F74 (ring kit) 22G44 (close couple) 30G28 (WTK close couple)
FLUE GAS VENTING SYSTEMS
www.ipexna.com• Concentric Vent Kits can be field modified, providing compliance with BOTH the appliance manufacturers’ and IPEX’s guidelines ACCESSORIES WALL TERMINATION KITS For a traditional vent style, IPEX’s PVC Wall Termination Vent Kits are available in convenient 2”, 2-1/2” and 3” sizes. These PVC kits require only two
System, Termination, Fuel, Vents, Venting, Concentric, Concentric vent, Vent termination, Flue gas venting systems
Concentric Vent Installation Guide - DiversiTech
media.diversitech.coma) The DiversiTech concentric vent termination kit is intended for use with Category IV high efficiency (condensing gas) furnaces or water heaters with exhaust temperatures up to and including 65°C (149°F), ULC S636 Class II. Failure to follow this warning could result in fire, personal injury or death.
Termination, Vents, Concentric, Concentric vent, Concentric vent termination
UBBINK™ VENT SYSTEM FOR RINNAI TANKLESS WATER …
documents.alpinehomeair.com24 224046 Raised Horizontal Termination Kit (“Snorkel”) (94LSi, R75LSi, R50LSi) VENT PIPE EXTENSIONS 7 224051 224260 10” Vent Pipe Extension 224052 224265 19.5” Vent Pipe Extension 224053 224270 39” Vent Pipe Extension 8 224054 224275 Telescoping Vent Length 9 224063 224255 90 Degree Elbow
Direct Exhaust Venting Kit Instructions - Weil-McLain
www.weil-mclain.comMaximum vent lengths apply for either 3” or 4” vent and air pipe. If using 3” pipe, provide 4”x 3” tapered reducers at boiler connections and at Weil-McLain vent/air cap termination. Boilers will derate as vent length increases — see rating data on Figure 123, page 129 in the boiler manual for derate amounts. SIDEWALL termination
Termination, Vents, Lewis, Weil mclain, Mclain, Weil mclain vent
Z-VENT Special Gas Vent System
www.z-flex.comZ-VENT® aae e a ae a Z-VENT® Special Gas Vent Page 6 Z-Quote™ is a revolutionary software solution that creates a detailed, dimensional, Z-VENT® system layout, accurate bill of material and quote proposal in minutes. Simply submit a completed design check list and our technical staff will provide you with a quote, detailed drawing with part call outs, and material list.
Installation & Operation Manual Models: 80 - 285 Starting ...
www.lochinvar.comInstallation & Operation Manual Models: 80 - 285 Starting Serial #H07H10040039 This manual must only be used by a qualified heating installer / service
Manual, Operations, Model, Installation, Installation amp operation manual models