Directive 067: Eligibility Requirements for Acquiring and ...

Directive 088: Licensee Life-Cycle Management

Directive 088: Licensee Life-Cycle Management (December 2021) 5. 5) Each licensee must report to the AER all its closure activities and closure spends for the previous calendar year by March 31 of every year, or as otherwise directed by the AER. 6) Each licensee must keep complete and accurate records of its closure activities and spending.

  Management, Closures, And closure

Directive 036: Drilling Blowout Prevention Requirements ...

Directive 036: Drilling Blowout Prevention Requirements and Procedures (March 2019) i. Release date: March 14, 2019 Effective date: March 14, 2019 Replaces previous edition issued January 31, 2018. Drilling Blowout Prevention Requirements and Procedures . Contents

  Blowout

Directive 087: Well Integrity Management

tubing, casing, packer seal, or wellhead seal assembly; meet the minimum pressure and duration requirements specified in table 1 when pressure …

  Management, Requirements, Directive, Well, Minimum, Wellhead, Integrity, Directive 087, Well integrity management

Manual 023: Licensee Life-Cycle Management

Liability Management Program s) and the licensee’s abandonment, remediation, and reclamation liabilities (as determined using . Directive 011: Licensee Liability Rating (LLR) Program: Updated Industry Parameters and Liability Costs). Magnitude of liability is either low, medium, or high. The thresholds are as follows: •

  Programs, Liability, Directive, Ratings, Licensee, Directive 011, Licensee liability rating

Directive 017: Measurement Requirements for Oil and Gas ...

Directive 017: Measurement Requirements for Oil and Gas Operations (May 2020) i Directive 017 . Release date: May . 12, 2020 Effective date: May . 12

  Requirements, Measurement, Directive, Directive 017, Measurement requirements for oil

Directive 020: Well Abandonment - Alberta Energy Regulator

level-A interval), an additional cement plug must be circulated on top of the uppermost previously abandoned zone. This cement plug must be a minimum length of 30 vertical metres and have a minimum volume of 1 m 3. The base of this plug must be located below the base of groundwater protection ( BGWP).

  Directive, Well, Cement, Abandonment, Directive 020, Well abandonment

Directive 056: Energy Development Applications and …

Directive 056: Energy Development Applications and Schedules (May 2021) i. Release date: May 18, 2021 Effective date: May 18, 2021 Replaces previous edition issued March 25, 2021 . Energy Development Applications and Schedules . Contents

  Development, Applications, Schedule, Directive, Energy, Directive 056, Energy development applications and, Energy development applications and schedules

Directive 051: Injection and Disposal Wells (1994-03 ...

Requirements for Activities within the Boundary of a Regional Plan or e-mail . regional.plans@aer.ca. This bulletin rescinds and replaces Bulletin 2012-22: Application Procedures for Approval of Activities Located In or Near the Boundaries of the Lower Athabasca Regional Plan, which is an earlier bulletin that was issued regarding the AER’s

  Lower, Plan, Regional, Lower athabasca regional plan, Athabasca, Plan regional

Directive 060: Upstream Petroleum Industry Flaring ...

Alberta Energy Regulator . 2 Directive 060: Upstream Petroleum Industry Flaring, Incinerating, and Venting (April 2021) 2.11.1 Limitations on Nonroutine …

SAFE METHOD: HOT HOLDING - Food Standards Agency

hot holding begins. Hot holding equipment is for hot holding only. It should not be used to cook or reheat food. Do you do this? Yes No : THINK TWICE! Hot food must be kept at 63°C or above, except for certain exceptions. When you display hot food, e.g. on a buffet, you should use suitable hot holding equipment to keep it above 63°C.

  Holdings