ELECTRIC MOTORS - BARTEC
Electric motors are of totally enclosed, fancooled (blow-over) type. Cooling is provided by fans blowing external air over the ribbed ou side surface (cooling system IC 411 according to IEC 60034-6 or EN 60 034-6). Electric motors up to 250 frame size are made of grey cast iron. Motors frame sizes of 280 and
Download ELECTRIC MOTORS - BARTEC
Information
Domain:
Source:
Link to this page:
Documents from same domain
Basic concepts for explosion protection - BARTEC
www.bartec.deBasic concepts for explosion protection. ... hard coal mining prompted the development of the basics of electrical explosion protection. The advantages of electricity were so convincing that intensive work ... of explosion protection - derived from the health and safety at work regula-tions - are concerned with workplaces. For this reason ...
II 2G Ex db eb IIC T6 Gb X - BARTEC
www.bartec.deMarking according directive 2014/34/EU according norm EN 60079-0 Marking of electrical equipment for use in potentially explosive atmospheres BARTEC GmbH Max-Eyth-Str ...
Marking of non-electrical explosion protected equipment ...
www.bartec.decarbon dust operation where there is a risk of explosion - I M1 I Ma disconnection where there is a risk of explosion - I M2 or M1 I Mb or Ma Gas groups IIA IIB IIC Permitted Equipment groups IIA, IIB, IIC IIB, IIC IIC ATEX Gases/Vapours NB1) II 1G Ex h IIC T6 Ga NB2) 18 ATEX 1234 X Dusts II 2D Ex h IIIC T120 °C Db X ISO (IECEx)
Marking of NEC electrical explosion protected equipment
www.bartec.demotors, fuses, switchgear, power electronics Gases, vapors Propagation of an explosion inside to the outside is excluded Flameproof Explosionproof UL 1203 (Div. 1+2) FM 3615 ANSI/UL-60079-1 Ex da Ex db Ex dc Junction and connection boxes, enclosures, motors, lights, terminals Gases, vapors Avoidance of arcs, sparks and excessive temperature
ComEx Actuating elements - BARTEC
www.bartec.de– DIN EN 60204-1: 2007 – DIN EN 60947-5-1: 2005 (VDE 0660 Teil 200) Pushbutton with imprint “NOT-AUS EMERGENCY STOP” “Pull to Release” 05-0003-000800 Pushbutton with imprint “ARRET” 05-0003-000802 Pushbutton yellow, unlabelled 05-0003-000801 Pushbutton black, unlabelled 05-0003-000803 Pushbutton red, unlabelled 05-0003-000804
ComEx Control Stations - BARTEC
www.bartec.deE Switching or illuminating module or terminal block FF 00 – without accessory 01 – protective metal shroud 02 – external earth connection 03 – shroud + external earth connection 10 – labelling by template 18 – locking device 33 – earth plate 99 – on request Selection Key ComEx Control Station 0 7 - 3 5 * A E * - * * * B C D * D ...
Kennzeichnung elektrischer explosionsgeschützter Geräte ...
www.bartec.deKennzeichnung elektrischer explosionsgeschützter Geräte (ATEX/IECEx) - bedeutet: NICHT möglich anzuwenden. + bedeutet: Anwendung möglich. 1) Kennnummer der notifizierten Stelle (Notified Body) zuständig für die Zertifizierung des Hersteller- Qualitätssystems (Kat. 1 und 2).
Marking of electrical explosion protected equipment …
www.bartec.deIECEx Gases/Vapours Ex db eb IIB T4 Gb IECEx ExCB3) 11.1234 X Dusts Ex tc IIIB T120 °C Dc IECEx ExCB3) 11.1234 X Subdivisions and classification of gases and vapours Gases and vapours Assignment of gases and vapours accordance to the ignition temperature Temperature class Maximum surface temperature (equipment) Permitted Temperature classes ...
Related documents
Hydraulic Considerations in Pumping System Design
cdn.ymaws.comn •Energy dissipated due to friction and turbulence during pump operation •Major Losses (Friction Losses) • Due to friction between pumped water and inner surface of piping • H f = 3.02 L D-1.167 (V/C h)1.85 (Hazen-Williams Formula) where: • L is length of pipe (feet) • D is diameter of pipe (square feet) • V is mean velocity (fps) • C h is Hazen-Williams friction coefficient ...
SUBMERSIBLE MOTORS - Franklin Electric
franklinwater.comAll Motors APPLICATION Franklin submersible motors are designed primarily for operation in the vertical, shaft-up position. During acceleration, the pump thrust increases as its output head increases. In cases where the pump head stays below its normal operating range during startup and full speed condition, the pump may create upward thrust.
Heater Element Specifications - Rockwell Automation
literature.rockwellautomation.commotors, submersible pumps, or motors with short locked rotor time capability. Class 30 overload relays should be used with motors driving high inertia loads, where additional accelerating time is needed and the safe permissible locked rotor time of the motor is within Class 30 performance requirements.
SEWERAGE MANUAL - DSD
www.dsd.gov.hk4.1.3 Submersible Pumping Stations 4.1.4 Screw Pumping Stations 4.2 WET WELL/ DRY PUMPING STATION DESIGN 4.2.1 Wet Wells 4.2.2 Hydraulics 4.2.3 Wet Well Volume and Control Levels 4.2.4 Arrangement of Suction Pipe 4.2.5 Dry Well 4.3 SUBMERSIBLE PUMPING STATION DESIGN 4.4 SCREW PUMPING STATION DESIGN 4.4.1 Key Design Parameters
Report on International Efficiency Efficiency Classes for ...
www.emsd.gov.hkSubmersible motors and smoke extraction motors with a temperature class above 400oC shall be excluded. In accordance with the Hong Kong electricity supply context, 50Hz motor is the focus. It is observed that the motors commonly used in Hong Kong are 4-poles. A graphical
STANDARD SCHEDULE OF RATES FOR THE YEAR 2020-2021
www.twadboard.tn.gov.in5 4 Openwell submersible pumpset without panel board 107-110 6 5 Horizontal Split Casing Centrifugal Pump (1500RPM) 111 7 6 Horizontal Squirrel cage Motor 1500RPM 112 8 7 Horizontal Squirrel cage Motor 1000RPM 113 9 8 Vertical Turbine pump for 1500RPM VHS motor 114 10 9 Vertical Hollow/ Solid Shaft motors for turbine pump 1500 RPM 115
Collection Systems Technology Fact Sheet: Sewers, Lift Station
www3.epa.govdry-pit or dry-well and submersible lift stations. In dry-well lift stations, pumps and valves are housed in a pump room (dry pit or dry-well), that is easily accessible. The wet-well is a separate chamber attached or located adjacent to the dry-well (pump room) structure. Figures 1 and 2 illustrate the two types of pumps.