EXCAVATION CHK LST
into the excavation. rolling E. Hard hats worn by all employees. F. Spoils, materials, and equipment set back at least of the excavation. 2 meters (6 feet) from the leading edge G. Barriers provided at all remotely located excavations, wells, pits, shafts, etc. H. Walkways and bridges over excavations 4 feet or more in depth are equipped
Download EXCAVATION CHK LST
Information
Domain:
Source:
Link to this page:
Documents from same domain
HVAC Duct Cleaning - National Institutes of Health
ors.od.nih.govDivision of Occupational Health and Safety . The dirty filter/vent above indicate a cleaning is needed and should be performed by a professional . DOHS Fact Sheet on . HVAC Duct Cleaning . National Institutes of Health • Office of Research Services (ORS) • Division of Occupational Health and Safety (DOHS) • Technical Assistance Branch (TAB)
Contractor Health and Safety Requirements
ors.od.nih.gova. Contractor Safety Program Assessment: The NIH is committed to providing a safe environment for its employees, guests, and patients. Safety, as demonstrated during previous contracts, may be used in the past performance evaluation of a Contractor. Contractors are required to enroll in the Contractor Safety Assessment Program (CSAP).
Guidance for the Selection of Laboratory Coats
ors.od.nih.govThis reference document provides a general overview for selection of laboratory coats. It does not alter or determine compliance responsibilities in OSHA standards or NIH’s Manual Chapter 1340. Because interpretations and policy may change over time, you should your consult with your Institute's Safety and Health Specialist.
Protocol for Use and Maintenance of Oxygen Monitoring …
ors.od.nih.govdisplacement of oxygen. At a minimum, the following factors should be used in determining if a device should be installed: manufacturer (e.g., magnet) guidance, volume of gas used, location of gas, and air changes/hour in the room/area. The 2008 NIH DRM notes that both ‘carbon dioxide manifold rooms…
ACTIVITY HAZARD ANALYSIS (AHA)
ors.od.nih.govACTIVITY HAZARD ANALYSIS (AHA) Activity/Work Task: Overall Risk Assessment Code (RAC) (Use highest code) Project Location: Risk Assessment Code (RAC) Matrix . ... " is the likelihood to cause an incident, near miss, or accident and identified as: Frequent, Likely, Occasional, Seldom or Unlikely . H = High Risk "
Computer Workstation Ergonomics: Self-Assessment Checklist
ors.od.nih.govSelf Assessment Computer Workstation Ergonomics: Self-Assessment Checklist . The goal of this self-assessment is to help you set up your workstation for optimal comfort and performance. For more information, refer to the . National Institutes of Health, Office of Research Services, Division of Occupational Health and Safety website.
Chemical Segregation Table
ors.od.nih.govChemical Segregation. Common Chemical Additional Concerns and Common Incompatible Possible Reaction if Examples Storage Recommendations Chemicals Types Mixed/Health Concerns . Class of Chemicals . Flammable Liquids . Ethanol, Ethyl Acetate, Methanol, Acetone, Benzene, Xylene, Toluene Diethyl Ether Tetrahydrofuran Acetonitrile Glacial Acetic Acid
Applicant Instructions for Completing Form HHS-745, “HHS ...
ors.od.nih.govApplicant Instructions for Completing Form HHS-745, “HHS ID Badge Request” Section A collects identifying information about Applicants needed to issue an HHS ID Badge. In some Federal agencies, Sponsors or other authorized offi cials will complete this section for Applicants. If …
NIH Chemical Hygiene Plan
ors.od.nih.govBSC Biological Safety Cabinets CFH Chemical Fume Hood CFR Code of Federal Regulations CHO Chemical Hygiene Officer ... eyes, or mucus membranes. Physical hazards include, but are not limited to, chemicals which are explosive, flammable, or corrosive. (Definition listed in . Appendix F “Glossary of Terms.”) III.
Safety and Health Program Audit Tool
ors.od.nih.govImplemented Evidence of Implementation . A mechanism is established to exchange information about hazards present in the workplace and measures in place to prevent or control them. for all contractors to use to report injuries, hazards, and concerns. Host employers include any safety - related specifications and qualifications requirements for
Related documents
Water Well Design and Construction
groundwater.ucdavis.eduwater well is a hole, shaft, or excavation used for the purpose of extracting ground water from the subsurface. Water may flow to the surface naturally after exca-vation of the hole or shaft. Such a well is known as aflowing artesian well. More com-monly, water must be pumped out of the well.
Underground Mining Methods and Equipment
www.eolss.netThe functions of inclined and vertical shafts are usually versatile in mining operations. Main levels are arranged for main haulage and connection between underground key ... mechanical excavation utilizing continuous miners, shearers, ploughs/plows, and so on, can be employed. In contrast, drilling and blasting are usually employed when the ...
Geotechnical Manual (GEO)
onlinemanuals.txdot.govManual Notice 2020-1 From: Graham Bettis, P.E., Director, Bridge Division Manual: Geotechnical Manual Effective Date: July 13, 2020 Purpose This manual provides policy for geotechnical investigation and design for project development.
An introduction to pipe jacking and microtunnelling
pipejacking.orgTable of indicative jacking lengths achievable between shafts for mechanised drives 4d) Guidelines for curved drives. 4e) Table illustrating pipe jacking excavation methods for dry and wet ground. 4 DESIGN AND CONSTRUCTION METHODS. 13 20. 22 5. PIPE JACKING PIPES 6. JACKING LENGTHS, LOADS AND TOLERANCES
LOUISIANA
wwwsp.dotd.la.govlouisiana standard specifications for roads and bridges 2016 edition state of louisiana department of transportation and development baton rouge
SPECIFICATIONS & GUIDELINES
dot.ca.gov• The excavation face shall have a sufficient length to allow for the installation of one (1) complete ring of liner plates, or one (1) complete set of ribs and lagging before advancing. • The contractor shall submit details and design information of the shield.
Chapter 8 Foundation Design
www.wsdot.wa.govBoth shallow (e.g., spread footings) and deep (piles, shafts, micro-piles, etc.) foundations are addressed. In general, the load and resistance factor design approach (LRFD) as prescribed in the AASHTO LRFD Bridge Design ... must remain, construction staging needs, excavation, shoring and falsework needs, other constructability issues).