Experiment5—CouplerDesign. - HIT
structed as a stripline with ground plane, spacing of B=3.2 mm, dielectric constant of r=4.7, T=0.035 mm, tanδ=0.02,character-istic impedance of 50 Ω,and center frequency of 1 GHz. Assuming a lossless component and a perfect termination: • Write down the S-parameters matrix of the coupler. • Calculate its ZOeand ZOo.
Download Experiment5—CouplerDesign. - HIT
Information
Domain:
Source:
Link to this page:
Documents from same domain
Superheterodyne Spectrum Analyzer and …
www.hit.ac.ilCONTENTS I Superheterodyne Spectrum Analyzer and Spectrum Analy-sis 3 1Introduction 4 1.1 Objectives..... 4 1.2 NecessaryBackground:..... 4
Education Kit EV3 LEGO MINDSTORM - תיטובור תכרע
www.hit.ac.il:םיפסונ םירושיק:םיפסונ םירושיק ROBOTC הנכות א ROBOTC for LEGO MINDSTORMS: http://www.robotc.net/download/lego/ ROBOTC a C Programming Language for Robotics: http://www.robotc.net/
RF Laboratory Manual - Passive Filter Design.
www.hit.ac.ilRF Laboratory Manual - Passive Filter Design. H. Matzner, S. Levy, H. Moalem and D. Ackerman. December 2008.
Experiment5—CouplerDesign.
www.hit.ac.il3. For a 20 dBthree sections edge coupled line directional coupler, con-structed as a stripline with ground plane, spacing of B=3.2 mm, dielectric constant of r=4.7, T=0.035 mm, tanδ=0.02,character- istic impedance of 50 Ω,and center frequency of 1 GHz.
Shimshon Levy October 2012 - לימודי תואר שני
www.hit.ac.ilChapter 1 SPECTRUM ANALYZER AND SPECTRUM ANALYSIS 1.1 Objectives Upon completion of the experiment the student will: Learn the basic concept of frequency domain measurements.
1 Frequency Modulation (FM)
www.hit.ac.ilSince frequency modulation is a nonlinear process, an exact description of the spectrum of an frequency-modulated signal for an arbitrary message signal is more complicated than linear process. However if s(t) is sinusoidal, then the instantaneous frequency deviation of the angle-modulated signal is sinusoidal
Related documents
PCI Express* Board Design Guidelines
www.linelayout.comdesign guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and
MT-031: Grounding Data Converters and Solving the Mystery ...
www.analog.comcircuit design techniques including proper signal routing, decoupling, and grounding. In the past, "high precision, low-speed" circuits have generally been viewed differently than so- ... transmission line techniques (microstrip or stripline) where controlled impedances are required.
Generic Standard on Printed Board Design - IPC
www.ipc.orgPrinted Board Design Developed by the IPC-2221 Task Group (D-31b) of the Rigid Printed Board Committee (D-30) of IPC Users of this publication are encouraged to participate in the development of future revisions. Contact: IPC 3000 Lakeside Drive, Suite 309S Bannockburn, Illinois 60015-1249 Tel 847 615.7100 Fax 847 615.7105 Supersedes: IPC-2221A ...
Xilinx UG393 Spartan-6 FPGA PCB Design Guide
www.xilinx.comSpartan-6 FPGA PCB Design and Pin Planning www.xilinx.com UG393 (v1.3) October 17, 2012 Xilinx is disclosing this user guide, manual, release note, and/ or specification (the "Documentation") to you solely for use in the development