Firestone Polyiso Insulation
can be attached with hot asphalt or low rise foam adhesive to various substrates, or mechanically fastened with Firestone fasteners and plates. PhysiCal PRoPERtiEs PRoPERty tEst MEthoD tyPiCal valuE density ASTM D 1622 2 pcf compressive strength* ASTM D 1621 20 psi dimensional stability ASTM D 2126 2% Max Moisture Vapor t ransmission ASTM E 96 ...
Download Firestone Polyiso Insulation
Information
Domain:
Source:
Link to this page:
Documents from same domain
UNA-CLAD METAL - firestonebpco.com
www.firestonebpco.comSTOCK PATTERN COLORS NON-STOCK PATTERN COLORS Available with minimum purchase amount and extended lead-time. Contact your local Sales Rep for more information.
AG - UltraPly TPO Roofing Systems Application Guide
www.firestonebpco.com2. Consult container labels, Safety Data Sheets (SDS) and Technical Information Sheets (TIS) for specific safety instructions for all products used on the project. 3. Keep all adhesives, sealants and cleaning materials away from ALL ignition sources (i.e., flames, fire, sparks, etc.). Do not smoke while using these materials. 4.
ISOGARD™ GL Insulation
www.firestonebpco.comAll Firestone polyisocyanurate foam insulations use EPA accepted blowing agents. Firestone ISOGARD GL incorporates a HCFC-free blowing agent that does not contribute to the depletion of the ozone layer (ODP-free). Method of Application: 1. Insulation shall be neatly fitted to all roof penetrations, projections and nailers. 2.
UltraPly™ TPO Walkway Pad - firestonebpco.com
www.firestonebpco.comPlease contact Firestone Technical Services at 1-800-428-4511 for further information. This sheet is meant to highlight Firestone products and specifications and is subject to change without notice. Firestone takes responsibility for furnishing quality materials which meet published Firestone product specifications.
ISOGARD™ HD Cover Board Coated Glass Facer High Density ...
www.firestonebpco.comStructural Concrete, 3000 psi (New & Existing) Please consult Membrane Design Guides on line at www.firestonebpco.comSteel, min. 22 ga to review specific information regarding fastener types appropriate for the type of deck and insulation in use. uge Lightweight Concrete* Plywood and OSB, min. ½" Gypsum, min. 2" NOT ACCEPTABLE
Attachment Guide Supplemental Increased Wind Speed ...
www.firestonebpco.comFirestone Attachment Guide November 29, 2021 Attachment Guide & Supplemental Increased Wind Speed Warranty Attachment Guide November 2021 NOTE: The contents of this guide are considered accurate at time of posting. All information contained within should be validated for accuracy as it relates to
UltraPly™ TPO Roofing Systems
www.firestonebpco.comNov 29, 2021 · Guide for Designers UltraPly TPO UltraPly TPO Platinum UltraPly TPO InvisiWeld™ ... the roof system and integration with the rest of the structure envelope. Firestone Building Products UltraPly TPO Roofing Systems - Guide for Designers ... compliance with specifications other than Firestone’s. 3. Hail coverage:
UltraPly™ Bonding Adhesive
www.firestonebpco.com6. Allow Bonding Adhesive to flash off until tacky. Touch down on the Bonding Adhesive surface with a clean, dry finger to be certain that the adhesive does not string. As you are touching the adhesive, pushing straight down to check for stringing, also push forward on the adhesive at an angle to ensure that the adhesive solvents have flashed
UltraPly™ TPO Membrane
www.firestonebpco.comUltraPly™ TPO Membrane Firestone Building Products | Sales: (800) 428-4442 | Technical (800) 428-4511 | www.firestonebpco.com TIS 201 6/8/2021
TIS 836 - TWIN JET
www.firestonebpco.comSpatter Application: Spatter Twin Jet at a rate of 60-70% coverage over the horizontal substrate and 75-85% at base tie-in locations, 2200 ft² (204 m²) to 2350 ft² (218 m²) per cannister set. • Do not apply Twin Jet Adhesive to the roof membrane. Keep lap areas of XR membrane clean and free of Twin Jet Adhesive overspray.
Related documents
RetroPlus Roof Board - Johns Manville
www.jm.comMechanically Fastened Urethane Adhesive Hot Asphalt Cold Applied Refer to the Application Guides and Detail Drawings for instructions. Packaging and Dimensions Sizes 4' x 4' (1.22 m x 1.22 m) 4' x 8' (1.22 m x 2.44 m) Thickness, nom ½" (1.27 cm) Board Weight, nom 9.9 lb (4.54 kg) 19.8 lb (9.07 kg) Coverage/Pallet 15.4 squares (143 m 2) 30.8 ...
DuPont Tyvek Mechanically-Fastened Water-Resistive and …
www.dupont.comMechanically-Fastened Water-Resistive and Air Barriers (Tyvek® WRBs) Product Dimensions Area DuPont™ Tyvek ® CommercialWrap® 5 ft x 200 ft 10 ft x 125 ft 1,000 sq ft 1,250 sq ft DuPont™ Tyvek ® CommercialWrap® D 5 ft x 200 ft 10 ft x 125 ft 1,000 sq ft 1,250 sq ft Self-Adhered Flashing Products Product Width
Pipe And Valve Identification
d37iyw84027v1q.cloudfront.netA mechanically applied, surface printed vinyl pipe marker. Snap-ons are used for pipes less than 6” outside diameter. Strap-ons are designed for pipes from 6” and greater Self-Sticking Pipe Markers Mechanically Applied Pipe Markers HARSH ENVIRONMENT General Purpose Mechanically Applied Mechanically Applied Self-Sticking Characteristic B-689
ROOFING SYSTEM APPROVAL - Miami-Dade County
www.miamidade.govSystem Type E(2): Anchor sheet mechanically fastened to deck, membrane adhered Anchor/Base Sheet: One or more plies of ASTM D 226 Type II or ASTM D 2626. Fastening: Per FBC 1518.2 & 1518.4 Nails and tin caps 12" grid, 6" o.c. at a minimum 4" head lap. (for base sheet only) Membrane: Elastoflex S6 G, hot asphalt applied
DensDeck Roof Board - Johns Manville
www.jm.comMechanically Fastened Urethane Adhesive Hot Asphalt Cold Applied Refer to the Application Guides and Detail Drawings for instructions. Packaging and Dimensions Size 4' x 8' (1.22 m x 2.44 m) Thickness, nom ¼" (6.4 mm) ½" (12.7 mm) 5 ...
Metal Sales Product Catalog
www.metalsales.us.comCONCEALED FASTENED PANELS ... Pittsburgh double flat locking mechanically seamed side lap Concealed clip designed for thermal movement Accommodates 1/2" to 6" blanket insulation Applies over open framing or solid substrate Finishes: PVDF and Acrylic Coated Galvalume ...
CertainTeed Low-Slope Roof Systems FLINTLASTIC® SA
www.certainteed.comsheet (mechanically fastened); PlyBase or MidPly may be used as a base ply (fully adhered, watertight). NOTE: PlyBase or MidPly may also be used as interply layers in three-ply systems, see Application of Interply (Optional). Mechanically Attached Base Beginning at the low point of the roof, mechanically fasten Flintlastic SA NailBase
Gluedown Installation Guidelines
www.karndean.comMechanically remove all paint back to the original base, prime and apply a compatible smoothing compound to a minimum of 1/8” (3 mm). 2. Wood Subfloors Standard Floorboards/Tongue and Groove Floorboards should be well secured, loose boards firmly fastened, and worn/broken boards replaced. Install a