General Purpose Input/Output (GPIO)
A General Purpose Input/output (GPIO) is an interface available on most modern microcontrollers (MCU) to provide an ease of access to the devices internal properties. ... Some of the features of the ports include: a standard logic tolerance of up to 5-V on both input and output, specific programmable control for GPIO interrupts which include
Download General Purpose Input/Output (GPIO)
Information
Domain:
Source:
Link to this page:
Documents from same domain
Using Microsoft Visual Studio to Create a Graphical User ...
www.egr.msu.eduUsing Microsoft Visual Studio to Create a Graphical User Interface ECE 480: Design Team 11 Application Note Joshua Folks April 3, 2015 Abstract: Software Application programming involves the concept of human-computer interaction and in this area of the program, a graphical user interface is very important. Visual widgets such as
Effects of temperature dependence of electrical and ...
www.egr.msu.eduEffects of temperature dependence of electrical and thermal conductivities on the Joule heating of a one dimensional conductor F. Antoulinakis,1 D. Chernin,2 Peng Zhang,1,a) and Y. Y. Lau1 1Department of Nuclear Engineering and Radiological Sciences, The University of …
ECE 410: VLSI Design Course Lecture Notes - egr.msu.edu
www.egr.msu.eduECE 410: VLSI Design Course Lecture Notes (Uyemura textbook) Professor Andrew Mason Michigan State University. ECE 410, Prof. A. Mason Lecture Notes Page 2.2 CMOS Circuit Basics nMOS gate gate drain source source drain pMOS
Power!Supply,!Arduino!MEGA!2560,! and!Stepper!Motors ...
www.egr.msu.edu• 12V 10Amp power supply • Stepper motors o Datasheet • Wires ! 3! Getting Started The Arduino board is the link between the power supply and stepper motors. Thus, it is important to understand the input/output pins of the microcontroller. As shown
no capabilities for “online” memory Write operations ...
www.egr.msu.eduECE 410, Prof. A. Mason Lecture Notes 13.7 Multi-Port SRAM • Allows multiple access to the same SRAM cell simultaneously. – Provide high data bandwidth.
Chapter 2. Design of Beams – Flexure and Shear
www.egr.msu.eduCE 405: Design of Steel Structures – Prof. Dr. A. Varma Chapter 2. Design of Beams – Flexure and Shear 2.1 Section force-deformation response & Plastic Moment (Mp) • A beam is a structural member that is subjected primarily to transverse loads and negligible
Introduction to Wireless Communications and Networks
www.egr.msu.edurepeater stations are placed along the path of a digital system at distances short enough to ensure that noise and distortion remain within a limit. The viability of regenerative repeaters is the main reason for the superiority of ... Base station receives the request and sends it to the MSC.
Combustion Examples - Michigan State University
www.egr.msu.eduCombustion Examples Example: Combustion of Butane with Specified Air to Fuel Ratio Butane is burned with air with 130% theoretical air. Balance the chemical reaction equation and determine the air to fuel ratio of the combustion process. Solution: We begin by writing our unbalanced theoretical chemical reaction equation for butane.
SHEET METALWORKING - Michigan State University
www.egr.msu.eduSheet-metal Operation . 7. Bending of Tube Stock. 2. Introduction • Cutting and forming thin sheets of metal usually performed as cold working • Sheet metal = 0.4 (1/64) to 6 mm (1/4in) thick • Plate stock > 6 mm thick • Advantage - High strength, good dimensional accuracy, good surface finish, economical mass
Design a simple DC power supply - Michigan State University
www.egr.msu.eduThe power supply that has been designed provides a good alternative to a more expensive power supply. The power supply has few components, covers a small area, and is very simple in design. Figure 5: Final Design. Works Cited “Dc Power Supply.” Test Equity. 2 Apr. 2009
Related documents
The GSPRs (General Safety and Performance Requirements ...
d2evkimvhatqav.cloudfront.netAn update or change to a standard should trigger the manufacturer to undertake a risk assessment of complying or not complying with the latest standard or version. The outcome of the risk assessment will help inform the decision of whether to apply the change. If the manufacturer decides to: > Update to the latest version of the standard, it
IS 14962-1 (2001): ISO General Purpose Metric Screw ...
law.resource.orgISO 68-1:1998, ISO general purpose scre w threads — Basic profile — Part 1:Metric screw threads. ISO 261:” ISO 262:” ISO 724: 998, 1S0 general purpose metric screw threads — General plan. 998, ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts. 993, ISO general purpose metric screw threads — Basic ...
Sample Partnership Agreement - USA Gymnastics
usagym.orgpurpose of operating a business known as: _____ (Partnership Business). The name of the Partnership (if different from name of Partnership Business) shall be: _____ (Partnership Name). 3. Nature of Partnership Business The Partnership Business will consist of …
International Consensus Standards
www.adc-int.org1.0 general provisions 1.1 scope and application 2 1.1.1 purpose 2 1.1.2 preservative acts 2 2.0 diving personnel medical and training requirements 2.1 general 4 2.2 commercial diving training requirements 4 2.2.1 entry-level qualifications 4 2.2.2 minimum required experience and proficiency 4 2.3 diver medical requirements 5 2.3.1 general 5
GENERAL STANDARD FOR FOOD ADDITIVES
www.bsmi.gov.twCODEX STAN 192 Page 2 b) Acceptable Daily Intake (ADI) is an estimate by JECFA of the amount of a food additive, expressed on a body weight basis, that can be ingested daily over a lifetime without appreciable health risk (standard man = 60 kg).4 c) Acceptable Daily Intake "Not Specified" (NS)5 is a term applicable to a food substance of very low toxicity which, on the …
GENERAL STANDARD FOR FOOD ADDITIVES CODEX STAN …
www.fao.orgGeneral Standard for Food Additives (GSFA) should be the single authoritative reference point for food additives. Codex commodity committees have the responsibility and expertise to appraise and justify the ... purpose in the manufacture, processing, preparation, treatment, packing, packaging, transport or holding of such food results, or may ...
Position Classification Standard for Supply Clerical and ...
www.opm.govPositions should be classified using the factor level descriptions contained in this standard. The Primary Standard and related classification standards (Grade Evaluation Guide for Clerical and Assistance Positions) are used to evaluate positions when the appropriate factor levels are higher or lower than those described in the standard.