HARDIPLANK Installation Instructions
gap and caulk the joint Nail 3/4" - 1" up from bottom of plank Fasten 16" o.c. Moderate contact or maximum 1/8" gap and caulk the joint BLIND NAIL: (All Lap Products) stud 16” or 24” o.c. 1 1/4” min. overlap blind nail space plank according to joint treatment with a 1/8” maximum gap 1” 1 1/4” overlap EZ Line alignment aid
Download HARDIPLANK Installation Instructions
Information
Domain:
Source:
Link to this page:
Documents from same domain
Section 504: Clothes Dryer Exhaust: 504.1 Installation.
www.structuretech1.comSection 504: Clothes Dryer Exhaust: 504.1 Installation. Clothes dryers shall be exhausted in accordance with the manufacturer’s instructions.
HARDIPLANK Installation Instructions
www.structuretech1.comMinimum overlap for Both Face and Blind Nailing min. 1 1/4” overlap weather-resistive barrier * nominal 2” x 2” wood furring 1” - 2” flashing
Early History of Attic Ventilation - Structure Tech Home ...
www.structuretech1.com1 Early History of Attic Ventilation William B. Rose Research Architect Building Research Council-School of Architecture University of Illinois at Urbana-Champaign
Table 501.3.3(2) Procedure to Determine Makeup Air ...
www.structuretech1.com16 Table 501.3.3(2) Procedure to Determine Makeup Air Quantity for Exhaust Equipment in Dwellings (Refer to Item 5 in Section 501.3.3 to determine applicability of this table)
HARDIPLANK Installation Instructions
www.structuretech1.com†For application over foam insulation, the length of the specified fastener ... FAILURE TO ADHERE TO WARNINGS, MSDS, AND INSTALLATION INSTRUCTIONS MAY LEAD TO SERIOUS PERSONAL INJURY. ... These documents should also be consulted for additional information concerning the suitability of this product for specific applications. JH91513SL 06/01
Related documents
2. Design of Welded Connections - American Welding Society
app.aws.orgin lap joints transferring stress between axially loaded parts shall be double-fillet welded (see Figure 2.5) ex-cept where deflection of the joint is sufficiently re-strained to prevent it from opening under load. 2.4.8.2 Minimum Overlap. The minimum overlap of parts in stress-carrying lap joints shall be five times
LiteAP™ AC Datasheet
dl.ubnt.comIn a cost-effective WISP deployment, the LAP-GPS is used as an Access Point in an airMAX ac Point-to-MultiPoint network. D atasheet 3 Hardware Overview ... Versatile Mounting The ball-joint mount of the LiteAP AC provides adjustment flexibility for versatile mounting options.
Florida Product Approval HardiePlank Lap Siding
www.floridabuilding.orgJOINT TREATMENT* (Required for ColorPlus ... ® lap siding is recognized as a suitable alternate to that specified in: the BOCA National Building Code/1999, the 1997 Standard Building Code, the 1997 Uniform Building Code, the 1998 International One- and Two-Family Dwelling Code, the 2003 International Building Code, and the 2003 International ...
ICC-ES Evaluation Report ESR-2290 - James Hardie Pros
www.jameshardiepros.comLap siding installed over walls constructed of concrete masonry units complying with ASTM C90 must be applied in accordance with Tables 5 through 10. lap The siding requires the use of a starter strip to set the first course on the proper angle and to create a drip edge. Vertical joints must be madeoff-stud by means of the tongue and groove joint.
Joint Flashing - Fiber Cement Products | James Hardie Pros
www.jameshardiepros.comMoisture management –Inherent in lap siding design is the provision of drainage at the laps and drying through the airspace that exists behind each plank. In line with this and fundamental water management principles, joint fl ashing behind fi eld butt joints
Detailed Drawings Single Ply - Tremco Roofing
www.tremcoroofing.comTPA-104 End Lap Detail TPA-105 T-Joint Detail TPA-108 Roof Perimeter Flashing Detail TPA-206 TremLock Fascia Edge Detail 8.4-7. Detailed Drawings Single Ply TPA-207 TremLine Edge Detail with Extender TPA-211 Gravel Stop WITH TPA Coated Metal TPA-213 Gravel Stop - TPA Coated Metal - Isometric TPA-220 Through Wall Scupper Detail