HST Stud anchor
HST Stud anchor 10 / 2012 135 values according ETAG 001, Annex C. To avoid this, it is recommended to use the anchor design software PROFIS anchor) The design method is based on the following simplification: No different loads are acting on individual anchors (no eccentricity) The values are valid for one anchor.
Download HST Stud anchor
Information
Domain:
Source:
Link to this page:
Documents from same domain
Page 1/8 Safety Data Sheet acc. to ISO 11014 - Hilti USA
www.hilti.comPage 2/8 Safety Data Sheet acc. to ISO 11014 Printing date 05/19/2015 Version number 5 Reviewed on 05/19/2015 (Contd. of page 1) 40.2.7 H319 Causes serious eye irritation.
Hilti. Outperform. Outlast.
www.hilti.comSelector Guide Through-Penetration Joint Reference Data Firestop Mortar (CP 637) Product description ... Concrete and masonry assemblies Expansion on setting (approx.)Walls and floors rated up to 4 hours ... Mix ratio (recommended, mortar to water):
ICC-ES Evaluation Report ESR-2269 - Hilti
www.hilti.com1.0 EVALUATION SCOPE Compliance with the following codes: 2018, 2015, and 2012 International Building Code ® (IBC) 2018, 2015, and 2012 International Residential Code® (IRC) For evaluation for compliance with codes adopted by the Los Angeles Department of Building and Safety (LADBS), see ESR-2269 LABC and LARC Supplement.
HILTI TECHNICAL BULLETIN
www.hilti.comMar 04, 2018 · )n ≤ 1, where n=5/3 for 3/8- and 1/2-inch diameters (No. 3 and No. 4 rebar) and n=1 for 5/8 and 3/4-inch diameter or No. 5 and No. 6 rebar. 9 The critical spacing, s cr, is the smallest anchor spacing where full load values may be used. The minimum spacing, s min, is the minimum anchor spacing for which values are
HIT-RE 500 V3 - Hilti
www.hilti.comSafety information for 2-Component-products 18/06/2020 US-OSHA - en 2/27 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If skin irritation or rash occurs: Get medical advice/attention. If eye irritation persists: Get medical advice/attention.
Hilti HIT-HY 200 with HIT-V
www.hilti.comAnchor rods HIT-V GR / -HCR) are available in variable length MIO M12 TE 16 M16 M20 M24 TE 40 M27 - TE 70 M30 compressed air gun or blow out pump, set of cleaning brushes, dispenser Drill hole to the required embedment depth with an appropriately sized Hilti TE-CD Or TE-YD hollow drill bit with Hilti vacuum attachment. This drilling
Hilti HIT-HY 200 with rebar
www.hilti.comHilti HIT-HY 200 with rebar Benefits - suitable for cracked and non- cracked concrete C 20/25 to C 50/60. - Approved automatic cleaning with the use of the hollow drill-bit high loading capacity, excellent handling HY 200-R version with extended curing time for rebar applications small edge distance and anchor spacing possible
KB-TZ2 TECHNICAL GUIDE
www.hilti.comKB-TZ2 Technical uide April 2021 5 Table 4 - Allowable Hilti carbon steel KB-TZ2 strength in uncracked concrete for hammer drill and core drill installations 1,2,3,4 Nominal anchor
OPENINGS IN COMPOSITE FLOOR DECKS - Hilti
www.hilti.comin-situ reinforced concrete topping. The decking not only acts as a permanent formwork to the concrete, but also provides sufficient shear bond with the concrete so that, when the concrete has cured, the two materials act together compositely to resist the loads on the deck. Openings in floor decks are a common part of any building.
HIT-1 ADHESIVE ANCHORING SYSTEM - Hilti
www.hilti.comHIT-1 ADHESIVE ANCHORING SYSTEM Technical Supplement PRODUCT DESCRIPTION Hilti HIT-1 is a hybrid adhesive mortar combining resin, hardener, cement, and water. It’s formulated for fast curing and easy installation in a wide range of concrete and masonry base materials with temperatures ranging from 32°F (0°C) up to 95°F (35°C).
Related documents
China’s Special Economic Zones - World Bank
www.worldbank.organchor regional development. Various management models have been followed. These include a) administrative management, with ... expansion depend on industry and market-focused planning. Planning also needs to include identification of capital investments and requirements
Expansion Joints Guide - BOA GROUP
www.boagroup.comexpansion joints decouple vibrations and structure-born noise from diesel engines, turbines, pumps and compressors, preventing their transfer ... dimensions of shaft structures or low cost solutions for anchor points. The multi-ply bellows has also a positive effect on the safety of the expansion joint.
HILTI HSA EXPANSION ANCHOR - Hilti United Kingdom
www.hilti.co.ukHSA Expansion anchor Everyday standard expansion anchor for uncracked concrete Anchor version Benefits HSA HSA-F HSA-R HSA-R2 (M6-M20) - Fast & convenient setting behaviour - Reliable ETA approved torqueing using impact wrench with the innovative SIW 6AT-A22 and SI-AT-A22 system for automatic torqueing - Small edge and spacing distances - High ...
HSL-3 EXPANSION ANCHOR - Hilti
www.hilti.com.auHSL-3 expansion anchor Ultimate-performance heavy-duty expansion anchor Anchor versions Benefits (M8 HSL-3 Bolt version -M24) - Suitable for cracked concrete C20/25 to C50/60 - Suitable for all dynamic loads: seismic C1 and C2, shock and fatigue - Can be installed with hammer or diamond drilling for same performance