I2C bus specifications - CERN
(2) The CBUS address has been reserved to enable the inter-mixing of CBUS compatible and I2C-bus compatible devices in the same system. I2C-bus compatible devices are not allowed to respond on reception of this address. (3) The address reserved for a different bus format is included to enable I2C and other protocols to be mixed.
Download I2C bus specifications - CERN
Information
Domain:
Source:
Link to this page:
Related documents
Interfacing FT2232H Hi-Speed Devices to I2C Bus
www.ftdichip.comThe physical layer of I2C bus is a simple handshaking protocol that relies upon open collector outputs on the bus devices and the device driving or releasing the bus lines, so a pull-up resistor is needed on each wire of the bus. I2C bus is a true multi-master bus including collision detection and arbitration to prevent data corruption
PCA9546A 4-channel I2C-bus switch with reset
www.nxp.comI2C-bus interface logic; compatible with SMBus standards Active LOW reset input 3 address pins allowing up to 8 devices on the I2C-bus Channel selection via I2C-bus, in any combination Power-up with all switch channels deselected Low Ron switches Allows voltage level translation between 1.8 V, 2.5 V, 3.3 V and 5 V buses
I2C-bus specification and user manual - NXP
nxp.com2.2 Manufacturer benefits I2C-bus compatible ICs not only assist designers, they also give a wide range of benefits to equipment manufacturers because: •The simple 2-wire serial I2C-bus minimizes interconnections so ICs have fewer pins and there are not so many PCB tracks; result — smaller and less expensive PCBs.
12-Bit DAC with EEPROM Memory in SOT-23-6
www.sparkfun.comOct 05, 2007 · The MCP4725 has a two-wire I2C™ compatible serial interface for standard (100 kHz), fast (400 kHz), or high speed (3.4 MHz) mode. The MCP4725 is an ideal DAC device where design simplicity and small footprint is desired, and for applica-tions requiring the DAC device settings to be saved
I2C Serial Interface 1602 LCD Module - handsontec.com
handsontec.comI2C Serial Interface 1602 LCD Module This is I2C interface 16x2 LCD display module, a high-quality 2 line 16 character LCD module with on-board contrast control adjustment, backlight and I2C communication interface. For Arduino beginners, no more cumbersome and complex LCD driver circuit connection.
18-Bit ADC with I2C Interface and Onboard Reference DS
ww1.microchip.comMar 26, 2009 · The devices operate from a single 2.7V to 5.5V power supply and have a two-wire I2C compatible serial interface for a standard (100 kHz), fast (400 kHz), or high-speed (3.4 MHz) mode. 16-Bit, Multi-Channel ΔΣ Analog-to-Digital Converter with …
THE I2C-BUS SPECIFICATION VERSION 2.1 JANUARY 2000
www.csd.uoc.gr6 Philips Semiconductors The I2C-bus specification 2.2 Manufacturer benefits I2C-bus compatible ICs don’t only assist designers, they also give a wide range of benefits to equipment manufacturers because: •The simple 2-wire serial I2C-bus minimizes interconnections so ICs have fewer pins and there are
INA3221 Triple-Channel, High-Side Measurement, Shunt and ...
www.ti.comsingle 2.7-V to 5.5-V supply, and draws 350 μA (typ) of supply current. The INA3221 is specified over the operating temperature range of –40°C to +125°C. The I2C- and SMBUS-compatible interface features four programmable addresses. Device Information(1) PART NUMBER PACKAGE BODY SIZE (NOM) INA3221 VQFN (16) 4.00 mm x 4.00 mm
PCF8574 Remote 8-Bit I/O Expander for I2C Bus datasheet ...
www.ti.comI2C or SMBus Master (e.g. Processor) Peripheral Devices RESET, ENABLE, or control inputs INT or status outputs LEDs SDA SCL INT A0 A1 A2 GND VCC P0 P1 P2 P3 P4 P5 P6 P7 Product Folder Sample & Buy Technical Documents ... • Compatible With Most Microcontrollers • Latched Outputs With High-Current Drive ... (I2C) is designed for 2.5-V to 6-V ...