INSTALLATION GUIDE
CLASS C FIRE RATED SYSTEM: In addition to self-adhered membrane, a minimum 30 lb. felt that meets ASTM D 226 Type II standard or a listed synthetic underlayment1 is required over the entire roof. If self-adhered membrane is required in the field of the roof (if there is
Download INSTALLATION GUIDE
Information
Domain:
Source:
Link to this page:
Documents from same domain
N DaVinci Slate - DaVinci Roofscapes
www.davinciroofscapes.comMembrane STARTER COURSE Each starter tile should be installed extending past the drip edge by approximately 1". However, if using an overhanging drip edge, the starter shingle can be allowed to overhang less if it is appropriate for the gutter system. The starter tiles should be installed with the DaVinci logo on top. The starter tiles should
Related documents
CHAPTER 15 ROOF ASSEMBLIES AND ROOFTOP STRUCTURES
www.ecodes.bizmechanically attached or adhered to the roof deck shall be designed to resist the design wind load pressures for components and cladding in accordance with Section 1609. 1504.3.1 Other roof systems. Roof systems with built-up, modified bitumen, fully adhered or mechanically attached single-ply through fastened metal panel roof systems, and
TECHNICAL GUIDE - Georgia-Pacific Building Products
www.buildgp.comDec 01, 2017 · For fully adhered and self-adhered “peel & stick” roofing systems, as well as hot mopped, cold mastic and torch-applied modified bitumen roofs, DensDeck Prime provides a stronger, more economical installation by reducing the
N DaVinci Slate - DaVinci Roofscapes
www.davinciroofscapes.comThis information is provided for the use of professional roofing contractors. ... Self-Adhered Membrane STARTER COURSE Each starter tile should be installed extending past the ... overhanging drip edge, the starter shingle can be allowed to overhang less if it is appropriate for the gutter system. The starter tiles should be installed with the ...
UltraPly™ TPO Roofing Systems
www.firestonebpco.comFeb 04, 2022 · e) Upon inspection and acceptance of the installed roof system by a Firestone Technical Representative, the warranty will be issued and dated based on the completion date of the roof installation reported by the roofing contractor. 2. Firestone’s inspection is to confirm the installation details of the roofing system for compliance with
Zip System Sheathing and Tape Installation Manual
www.huberwood.comZIP SYSTEM ® SHEATHING // OVERVIEW . ZIP System ® sheathing panels are orientedstrand board (OSB), wood structural panels with built-in protective overlays that eliminate the need for building wrap or roofing felt. Install the panels, tape the seams with ZIP System ™ flashing tape, and the building is rough dried-in. When used on a wall ...
DensDeck Roof Board - Johns Manville
www.jm.comFlame Spread E 84 0 Smoke Developed E 84 0 Non combustible in accordance with ASTM E 136 RS-5594 2-20 (Replaces 12-19) Meets the requirements of ASTM C 1177 Note: Technical information on this data sheet is intended to be used as a general guideline only and is subject to change without notice. Contact your JM Sales Representative for further ...
ProtectoR HD - Insulation Systems, Commercial Roofing and ...
www.jm.comMeets the requirements of ASTM C 1289, Type II, Class 4, Grade 1 8 ft. 0 in. 48.0 in. 30.0 in. 12.0 in. 24.0 in. 4 ft. 0 in. 12.0 in. 48.0 in. 12.0 in. 4 ft. 0 in. 12.0 in. 8 per 4'x 8' board achieves FM 1-90 with adhered reinforced membrane or FM 1-75 with adhered non-reinforced membrane applications over a min. 22 ga steel deck or structural ...