Example: air traffic controller
TECHNICAL GUIDE - Georgia-Pacific Building Products
Dec 01, 2017 · For fully adhered and self-adhered “peel & stick” roofing systems, as well as hot mopped, cold mastic and torch-applied modified bitumen roofs, DensDeck Prime provides a stronger, more economical installation by reducing the
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
SHAFTLINER FOR SHAFTWALL/STAIRWELL SYSTEMS
www.buildgp.comNote that the edges of the panel are beveled to help guide the panel into the slotted and tabbed section of the stud. 6. Progressively install succeeding studs and panels as described above until the wall section is enclosed. The final panel section may be secured with 1-5/8” (41 mm) Type S screws or tabs from the J track at 24” (610 mm) o ...
Technical Service Hotline 1.800.225.6119 or www.gpgypsum
www.buildgp.comassembly installation instructions). Primary Uses Because of the superior performance of DensGlass Sheathing, it is specified for exterior walls, ceilings and soffits in a wide variety of applications. These include exterior insulation and finish systems (EIFS); cavity brick or stone veneer applications;
TECHNICAL GUIDE - Georgia-Pacific Building Products
www.buildgp.cominstallation. DensGlass Sheathing is the ideal substrate for a wide variety of air and water-resistive barriers including building wraps, fluid applied coatings, self-adhering membranes and spray foam applications. See page 10 for details. Easy to Handle DensGlass Sheathing is lightweight and easy to handle.
Densglass Shaftliner Area Walls Technical Guide
www.buildgp.comBuilding Code (IBC) Section 706, “Fire Walls.” The Area Separation Wall assembly using DensGlass Shaftliner panels is listed in the UL Fire Resistance Directory under UL Design U373 or U375, the ULC Fire Resistance Directory ULC Design No. W312 and the
Technical Guide: DensArmor Plus® High-Performance Interior ...
www.buildgp.comof Gypsum Panel Products” and ASTM C840 “Standard Specifi cation for Application and Finishing of Gypsum Board for Non-Fire Rated Construction.” For best results, abut DensArmor Plus panels against regular paper-faced drywall only at inside or outside
Stamps/Signatures
www.buildgp.comFIRE SAFETY CAUTION Passing a fire test in a controlled laboratory setting and/or certifying or labeling a product as having a one-hour, two-hour, or any other fire resistance or protection rating and, therefore, as acceptable for use in certain …
DensShield® Tile Backer Installation Instructions
www.buildgp.comDS001. Note: Shower pan or rubber membrane must be adequately sloped to the open drain or weep hole detail to permit proper water drainage. Leave a 1⁄89 (3 mm) gap between DensShield Tile Backer and the shower pan. • DensShield Tile Backer is not to be used in shower curbs. • DensShield Tile Backer panels can be installed in the shower
Technical Service Hotline 1.800.225.6119 or www.densdeck
www.buildgp.commanufacturer’s specifications for full mopping applications and temperature requirements. ... * Testing was done in accordance with FM approvals 4470, Appendix C: Small Scale Tests, Membrane ... with the ANSI/UL 1256 Steiner Tunnel test. For additional information concerning
Related documents
ProtectoR HD - Insulation Systems, Commercial Roofing and ...
www.jm.comMeets the requirements of ASTM C 1289, Type II, Class 4, Grade 1 8 ft. 0 in. 48.0 in. 30.0 in. 12.0 in. 24.0 in. 4 ft. 0 in. 12.0 in. 48.0 in. 12.0 in. 4 ft. 0 in. 12.0 in. 8 per 4'x 8' board achieves FM 1-90 with adhered reinforced membrane or FM 1-75 with adhered non-reinforced membrane applications over a min. 22 ga steel deck or structural ...
N DaVinci Slate - DaVinci Roofscapes
www.davinciroofscapes.comThis information is provided for the use of professional roofing contractors. ... Self-Adhered Membrane STARTER COURSE Each starter tile should be installed extending past the ... overhanging drip edge, the starter shingle can be allowed to overhang less if it is appropriate for the gutter system. The starter tiles should be installed with the ...
UltraPly™ TPO Roofing Systems
www.firestonebpco.comFeb 04, 2022 · e) Upon inspection and acceptance of the installed roof system by a Firestone Technical Representative, the warranty will be issued and dated based on the completion date of the roof installation reported by the roofing contractor. 2. Firestone’s inspection is to confirm the installation details of the roofing system for compliance with
CHAPTER 15 ROOF ASSEMBLIES AND ROOFTOP STRUCTURES
www.ecodes.bizmechanically attached or adhered to the roof deck shall be designed to resist the design wind load pressures for components and cladding in accordance with Section 1609. 1504.3.1 Other roof systems. Roof systems with built-up, modified bitumen, fully adhered or mechanically attached single-ply through fastened metal panel roof systems, and
Zip System Sheathing and Tape Installation Manual
www.huberwood.comZIP SYSTEM ® SHEATHING // OVERVIEW . ZIP System ® sheathing panels are orientedstrand board (OSB), wood structural panels with built-in protective overlays that eliminate the need for building wrap or roofing felt. Install the panels, tape the seams with ZIP System ™ flashing tape, and the building is rough dried-in. When used on a wall ...
INSTALLATION GUIDE
www.davinciroofscapes.comCLASS C FIRE RATED SYSTEM: In addition to self-adhered membrane, a minimum 30 lb. felt that meets ASTM D 226 Type II standard or a listed synthetic underlayment1 is required over the entire roof. If self-adhered membrane is required in the field of the roof (if there is
DensDeck Roof Board - Johns Manville
www.jm.comFlame Spread E 84 0 Smoke Developed E 84 0 Non combustible in accordance with ASTM E 136 RS-5594 2-20 (Replaces 12-19) Meets the requirements of ASTM C 1177 Note: Technical information on this data sheet is intended to be used as a general guideline only and is subject to change without notice. Contact your JM Sales Representative for further ...