Installation Instructions - Painless Performance
Details about the 4L60E and 4L80E Kit Contents Photo 5 Picture and List of what’s provided in this kit. Transmission Harness 6-10 Step-By-Step Instruction Vehicle Harness 11-13 Step-By-Step Instruction EFI Connections 14-15 Step-By-Step Instruction/Diagram 3 Carb or Diesel Connections 16-17 Step-By-Step Instruction/Diagram 4
Download Installation Instructions - Painless Performance
Information
Domain:
Source:
Link to this page:
Documents from same domain
Manual #90567 For Installing: Part #30830
www.painlessperformance.com7 Figure 1 C.S.I. Harness Schematic CONTENTS OF THE PAINLESS C.S.I. WIRE HARNESS KIT Refer to the list below to take inventory of all the parts in the kit. If anything is found to be
For Installing: #10127 Customizable Mopar Chassis …
www.painlessperformance.comWire Harness Installation Instructions For Installing: #10127 Customizable Mopar Chassis Harness 21 Circuit Manual #90542
Wire Harness Installation Instructions - Painless …
www.painlessperformance.comWire Harness Installation Instructions For Installing: #20110 Classic Customizable Chevy II/Nova 1966-67 Harness 21 Circuit Manual #90522
Wire Harness Installation Instructions - Painless …
www.painlessperformance.comWire Harness Installation Instructions For Installing: Part #20120 22 Circuit Ford Mustang (1965- 1966) Manual #90526
Wire Harness Installation Instructions - Painless …
www.painlessperformance.comWire Harness Installation Instructions For Installing: #10101 Classic Customizable Harness-GM Keyed Column-21 Circuit #10102 Classic Customizable Harness-Non GM Keyed Column-21 Circuit
175 o OFF THERMOSTAT INSTALLATION …
www.painlessperformance.com1 2501 Ludelle Street Fort Worth, Texas 76105 . 817-244-6212 phone . 817-244-4024 fax . 800-423-9696 Tech . E-Mail: painless@painlessperformance.com . Web: www.painlessperformance.com
Manual #90560 For Installing: #10111 Direct Fit Jeep YJ ...
www.painlessperformance.com7 Sections are divided into subsections and Paragraphs.Throughout these instructions, the Figure numbers refer to pictures and the Diagram numbers refer to illustrations.Figure numbers correspond to the Section number the are covered in. Always pay special and careful
HIGH AMPERAGE ALTERNATOR KIT (140-190 AMPS)
www.painlessperformance.com2 onto the output post of the alternator. This connection can be seen in Figure 1 on the next page and can be accomplished one of two ways: #1 Install each wire separately • Slide the rubber boot and/or a piece of the smaller sized heat shrink onto the wire found in the kit.
Wire Harness Installation Instructions
www.painlessperformance.com3.0 CONTENTS OF THE PAINLESS WIRE HARNESS KIT Refer to the list below to take inventory of all the parts in the kit. If anything is found to be missing, contact the dealer the kit was purchased
80230 - painlessperformance.com
www.painlessperformance.comPainless Performance Limited Warranty and Return Policy Chassis harnesses and fuel injection harnesses are covered under a lifetime warranty. All other products manufactured and/or sold by Painless Performance
Related documents
Back-Up Light or Neutral Safety Switch Kit Installation ...
www.lokar.comNOTE: This Kit offers the choice of a Back-Up Light Switch OR a Neutral Safety Switch, Not Both! 5/16"-18 x 1-1/4" This Kit will work with the Lokar Adjustable Column Shift Linkage EXCEPT TH400, 700-R4, 4L60E and 4L80E. Refer to Fig. 1 for the component names. Switch Installation: Step 1: Install the bracket with the switch: