INSTALLATION MANUAL
temperature rise range. Only c onnect the furnace to a duct system which has an external static pressure within the allowable range, as specified on the furnace rating plate. 8. When a furnace is installed so t hat supply ducts carry air circulated by the furnace to areas outside the space containing the furnace,
Download INSTALLATION MANUAL
Information
Domain:
Source:
Link to this page:
Documents from same domain
Outdoor Tankless Water Heater Operation and …
www.questargas.comTemperature Controller 6 VB Series Outdoor LS Manual MC-91-1US & MCC-91-1US The MC-91 controller is the standard temperature controller that is supplied with the water heater.
INSTALLATION AND SERVICE MANUAL J30-05373 …
www.questargas.comINSTALLATION AND SERVICE MANUAL INDOOR GAS-FIRED DUCT FURNACE (NATURAL OR POWER VENTED) (S) DISM-15 J30-05373 Model No. Serial No. FOR YOUR SAFETY The use and storage of gasoline …
INSTALLATION MANUAL
www.questargas.com2. Install this furnace only in a location and position as specified in these instructions. 3. A gas-fired furnace for installation in a residential garage must be installed as specified in these instructions. 4. Provide adequate combustion and ventilation air to the furnace space as specified in these instructions. 5.
MODEL 340MAV, 350MAV, 355MAV CONDENSING GAS …
www.questargas.comJunction box for 115-v electrical power supply. Transformer (24v) behind control center provides ... sumption on extremely cold days. The few degrees at the top of your thermostat “comfort level” are the most costly degrees to obtain. When room temperature drops
MODELS 373LAV, 376CAV DOWNFLOW/HORIZONTAL and …
www.questargas.comcontrol door. (See Fig. 10.) b. Upflow— remove control door. (See Fig. 11.) 5.The gas valve will have EITHER a control knob or control switch to turn off and on. Turn the control knob or switch on the gas valve to the OFF position and wait 5 min-utes. (See Fig. 12 or 13.) 6.After waiting 5 minutes, turn the control knob or switch on the gas
40 80% and 90% Gas Furnaces & Accessories GUIA, GCIA, …
www.questargas.comAMANA HEATING & AIR CONDITIONING CALL and ask for FAYETTEVILLE, TN 37334 Consumer Affairs WARNING CAUTION. PRODUCT IDENTIFICATION 4 Rev. 1 This section will identify the models covered and the changes per each model group from one release to the next. Model # Manufacturing # Description
Installer's Guide - Upflow/Horizontal and Downflow ...
www.questargas.comconnected to the venting system being placed into op-eration, while all other appliances connected to the vent-ing system are not in operation: 1. Seal any unused openings in the venting system. 2. Inspect the venting system for proper size and hori-zontal pitch, as required in the National Fuel Gas Code, ANSI Z223.1/ NFPA 54 or the CAN/ CGA B149
Owner’s Manual S Top-Vent Gravity Wall Furnace
www.questargas.comavailable (either natural or L.P. gas). DO NOT convert the furnace from natural gas to L.P. gas or from L.P. gas to natural gas without the proper manufacturer’s gas conversion kit. Combustion air is drawn in from the room where the furnace is located and is vented out of the top of the furnace vertically through vent -----
Visit www.carrier.com Installation, Start-Up, and ...
www.questargas.com4" typ 11 ⁄ 16 7 ⁄ 16 " 24 3 ⁄ 16 " bottom inlet 18 1 ⁄ 4 " 22 11 ⁄ 16 " condensate drain trap location (downflow & horizontal right) or alternate 1 2-in. dia gas conn 2-in. combustion- air conn 1 ⁄ 2-in. dia gas conn 7 ⁄ 8 power conn 1 ⁄ 2-in. dia thermostat entry 2-in. vent conn dimple locators for horizontal hanging 1 4 1 ...
Installation Manual
www.questargas.comThe PG9MAB Multipoise Condensing Gas-Fired Furnaces are CSA (formerly AGA and CGA) design-certified for natural and propane gases (see furnace rating plate) and for installation in alcoves, attics, basements, closets, utility rooms, crawlspaces, and garages. The furnace is factory-shipped for use with natural gas.
Related documents
NORME EUROPÉENNE 1092-1 EN DAAD STAN EUROPEAN
www.htcflange.comflanges in PN designations PN 2.5 to PN 100 and nominal sizes from DN 10 to DN 4000. This standard specifies the flange types and their facings, dimensions. tolerances. threading. bolt sizes. flange jointing face surface finish. marking. materials. pressure/ temperature ratings and approximate flange masses.
Flanges and their joints — Circular flanges for pipes ...
www.worldwidemetric.commanufacture of flanges are given in Table 9 and their corresponding Pressure/Temperature ratings are given in Annex G (normative). Additional materials that are widely in used in Europe are listed in Annex D (informative) but BS EN 1092-1:2007 contains no corresponding Pressure/Temperature information for …
BOLT & STUD DIMENSIONS FOR ANSI FLANGES
www.rhinofitt.co.ukCARBON STEEL PIPE FLANGES TO ANSI B16.5 (BS 1560) FORGINGS TO ASTM A105 - Not recommended for prolonged use above 427qC FORGINGS TO ASTM A350 - LF2 - Not to be used above 343qC ... IN THESE LARGE DIAMETERS DO NOT IMPLY SPECIFIC TEMPERATURE/PRESSURE RATINGS Inch/Metric Bolting interchangeable for ANSI B16.5 …
Technical Specifications Rev. F - 02/2021 Masoneilan 35002 ...
dam.bakerhughes.comBody Pressure Rating: ASME Class 600 (per B16.34) standard (1 in.-12 in.) (DN 25-300), except for flanged construction: valve rating is limited by flange rating End Connections: • threaded – NPT for ASME Class 600 rated connections (1 in.) (DN 25) • flangeless – clamps between ASME Class 150, 300 or 600 rated flanges
Schedule 80 CPVC Technical Information Schedule 80 CPVC ...
dpk3n3gg92jwt.cloudfront.netThe pressure ratings given above are for water, non-shock, @ 73°F. The specifi ed derating factors for CPVC are suitable for pipe conveying water at elevated temperatures. To determine elevated temperature rating, multiply 73°F [23°C] pressure rating by appropriate factor shown in the table for desired operating temperature.
Plastics - Charlotte Pipe
www.charlottepipe.comJan 11, 2022 · 2. INTRODUCTION. Plastics Technical Manual. Charlotte Pipe ® has been relentless in our commitment to quality and service for more than a century. Through the years
Daniel Senior Orifice Fitting Technical Guide
www.emerson.comCompanion flanges are available upon request. Figure 1: Method of aligning meter tube flange to Orifice Fitting Flange A. Meter tube flange B. Fitting flange Table 2: Pressure ratings available by line size for Daniel Senior Orifice Fittings Line size (in) …
Micro Motion ELITE Coriolis Flow and Density Meters
www.emerson.comSensor maximum working pressure for super duplex models (Y) Model ASME B31.3 compliance ASME B31.1 compliance CMFHC2Y, CMFHC3Y 2,320 psig (159.96 barg) n/a Temperature and pressure de-ratings Note The ratings in this section apply to the combined sensor and process connection to ensure that the meter does not exceed the limits of either component.
INDD B31.1 92 2595512 0078031 7T0 M ADOPTION NOTICE ...
www.nrc.gov102.2 Pressure-Temperature Ratings for Piping Components . .11 102.3 Allowable Stress Values and Other Stress Limits for Piping Components .. 12 102.4 Allowances .. 13 Part 2 Pressure Design of Piping Components. 16 103 Criteria for Pressure Design of Piping Components . .16 104 Pressure Design of Components .. 16