Installation, Operation, and Maintenance
This booklet describes proper installation, operation, and maintenance procedures for air cooled systems. By carefully reviewing the info rmation within this manual and following the instructions, the risk of improper operation and/or component damage will be minimized. It is important that periodic maintenance be performed to
Download Installation, Operation, and Maintenance
Information
Domain:
Source:
Link to this page:
Documents from same domain
Chiller perormancf e testing program - Trane
www.trane.com2 Chiller performance testing Trane is the global chiller leader Trane has manufactured centrifugal chillers in La Crosse since 1938. Much more than a
Water-Cooled Liquid Chiller Model CVGF 400 to …
www.trane.comIntroducing Trane’s Model CVGF Centrifugal Water Chiller Introduction The basic gear driven centrifugal water chiller design was introduced in 1976 and has been
3-D™ SCROLL COMPRESSOR NOMENCLATURE - …
www.trane.com3-D™ SCROLL COMPRESSOR NOMENCLATURE C S H A 1 5 0 K 0 * 0 0 Digit1 23 456789 101112 Digit 1 C ♦ Positive displacement …
Trane® Voyager
www.trane.comTrane combines technological innovation with legendary reliability and performance to create the lowest cost of ownership. Trane® Voyager™ rooftop units not only offer the lowest installed cost, they also can reduce
Packaged Cooling with Electric Heat Rooftop Units
www.trane.comPackaged Cooling with Electric Heat Rooftop Units Voyager™ 12½ - 25 Tons - 60 Hz December 2003 RT-PRC002-EN
Packaged Cooling with Electric Heat Rooftop Units
www.trane.comPackaged Cooling with Electric Heat Rooftop Units Precedent ™ 3 - 10 Tons — 60 Hz March 2003 RT-PRC005-EN
Air Conditioners - Trane
www.trane.comThe XV20i shown is for illustration purposes only. Please note that features and components may vary by model. As part of our continuous product improvement, Trane reserves the right to change specifications and design without notice.
Split System Heat Pumps
www.trane.comSSP-PRC001-EN 5 Odyssey air handler versatility is fur-ther increased by a complete line of accessories designed to match and install smoothly:
Split System Cooling Units - Heating and Air …
www.trane.comSplit System Cooling Units TTA075A-TTA200B Air Handlers TWE050A-TWE200B 50 Hz Split System Cooling Units December 2000 SS-PRC003-EN
Trane Packaged Systems - Heating and Air …
www.trane.comFlexible enough to install where you need it. Tough enough to be a Trane. Trane packaged heating and cooling systems give you everything in one.
Related documents
Commercial Kitchen Hood Installation and Maintenance …
larkinhoods.comHood Options 1.2 Front Perforated Supply Plenum (FPSP) Hang FPSP using all thread rod against the upper front of the hood. Attach plenum to channel located on the front edge of the hood. Collars maybe shipped mounted or loose. If the collars are loose, install diffuser plate, attach collar to the plenum…
COLEMAN®-MACH® AIR CONDITIONERS - Airxcel
old.rvcomfort.comthe ceiling plenum. The ceiling plenum must be located directly below the roof opening used for mounting the roof top unit. All manual controls have been removed from the ceiling plenum. They have been replaced with control relays. The relays are …
L4064B Universal Combination Fan and Limit Controllers
customer.honeywell.comIf plenum surface temperature exceeds 190 O F (88 O C), heat insulating material or a mounting bracket must be u s e d . MOUNTING The device may be mounted either on the plenum surface or with a bracket (rigid or swivel). SURF ACE MOUNTING Hole in plenum should be just large enough to accommodate the 3/4 in. (19.1 mm) diameter element tube, Fig. 1.
Cisco TelePresence Ceiling Microphone Installation Sheet
www.cisco.comIf mounted above the ceiling, the microphone cable must be Plenum Rated (US only). Microphone pickup range We recommend a horizontal pickup range for the microphone of maximum 14 t f4(3. m.) For larger rooms that require more than one ceiling microphone When using more than one ceiling microphone, mount the unit with a spacing of 81–4 t f 2(4 ...
Installation & Maintenance Manual - Montigo
www.montigo.cominstructions laid out in this Installation, Operation and Maintenance Manual and retain it for your future reference. Pay special attention to all cautions, warnings, and notices throughout this manual intended to ensure your safety. This manual covers installation, operation and maintenance. Lighting,
Zone Panel Professional Installation Guide
customer.honeywell.comInstallation uide 69-2198—052 MOUNTING Mount the HZ432 TrueZONE panel near the HVAC equipment; locate it on a wall, stud, roof truss, or cold-air return. NOTE: The HZ432 TrueZONE panel can be mounted in any orientation; level it for appearance only. 1 2 Separate the zone panel cover from the base, and use the base as a template to drill ...
LARGE FAN POWERED HUMIDIFIER MODEL 700M AND 700A
docs.electronicaircleaners.comINSTALLATION OPTIONS Typical Installation Alternate Installation COOLING COILS IN WARM AIR PLENUM Aprilaire to be installed as shown in relation to cooling coils. RECOMMENDED WIRING DIAGRAMS (SEE STEP 6 ON BACK AND“HUMIDIFIER CONTROL SAFETY AND INSTALLATION INSTRUCTIONS”FOR DETAILED WIRING INSTRUCTIONS) …
Model 800 Steam Humidifier Installation & Maintenance ...
docs.smoe.orgInSTallaTIon InSTRUCTIonS *Velocity in feet per minute = Duct airflow volume in cubic feet per minute / duct area in square feet . Example: 1,200 cfm through 16” x 12” duct = 1,200/(12 x 16/144 sq . in ./sq ft .) = 1,200/1 .333 = 900 fpm
69-2631ES 03 - HE360 Humidifier and Installation Kit
www.honeywellstore.com• Select a location for the humidistat on the return plenum or on the wall in the living space. — Mounting on the return plenum is the easiest installation for the control wiring circuit. For return duct mounting, the humidistat should be mounted upstream from the
Installation, Operation, and Maintenance
www.trane.comThis booklet describes proper installation, operation, and maintenance procedures for air cooled systems. By carefully reviewing the info rmation within this manual and following the instructions, the risk of improper operation and/or component damage will be minimized. It is important that periodic maintenance be performed to