INSULATION FOR THE BUILDING ENVELOPE
(ASTM E331, AATCC Test Method 127) • Class A Flame Spread and Smoke Developed Indices per IBC Chapter 8, Interior Finishes (1” min.) • 1, 2, 3 or 4 hour Fire Rated Assemblies as shown in the UL Fire Resistance Directory. NOTE: For details, requirements and/or limitations, refer to Third-Party Evaluation Reports
Download INSULATION FOR THE BUILDING ENVELOPE
Information
Domain:
Source:
Link to this page:
Documents from same domain
PRODUCT DATA SHEET Sika® Primer-207
usa.sika.comIMPORTANT NOTE If Sika® Primer-207 is used below 5 °C further testing under worst case conditions are man-datory. Sika® Primer-207 is a moisture reactive sys-
Sikadur Epoxies Application Guide - Sika …
usa.sika.comSikadur® Epoxies Application Guide LPL = Long Pot Life cps = centipoise Reference approximate viscosity water = 1 cps olive oil = 100 cps motor oil = 1000-2000 cps Crack Repair Patching Overlay Bonding Adhesive Anchor Bolts Base Plate Grouts USDA Approved Potable Water Approved ASTM C-881 Interior Exterior Int. Exterior Type …
Liquid Seam Sealant - Sika AG
usa.sika.comConstruction Sikaflex® 110 Liquid Seam Sealant Description Sikaflex 110 Liquid Seam Sealant is a non-shrinking, 100% solids, solvent free polyether based, moisture curing, elastomeric sealant. It forms a weather-tight seal when applied over sheathing board joints.
Part 1 - General - Sika AG
usa.sika.comA. Sikadur Injection Gel as manufactured by Sika Corporation, 1682 Marion Williamsport Road, Marion, Ohio 43302 is considered to conform to the requirements of this specification.
PRODUCT DATA SHEET SikaTop®-123 Plus
usa.sika.com0 g/l (EPA method 24) LIMITATIONS Do not use solvent-based curing compound. Size, shape and depth of repair must be carefully considered and consistent with practices recommended by ACI or ICRI. For additional information on substrate preparation, refer to ICRI Guideline No. 310.2R. If aggressive means of substrate preparation is
SikaSwell S-2 SikaSwell S-2
usa.sika.comApplication Recommended application temperatures: 50°-90°F. Extrude material using Sika MK-5 bulk caulking gun or other approved bulk gun. Cut the nozzle to obtain a triangular extrusion section with a size fulfilling effective needs (or use nozzle included in carton of SikaSwell S-2). Apply a uniform, continuous bead to the hardened concrete.
PRODUCT DATA SHEET Sikalastic®-710 Base
usa.sika.comMetal - Should be thoroughly cleaned by grinding or blast cleaning to near white metal (SSPC SPS-10). Priming Primer Selection - Determine maximum moisture content of concrete substrate by weight with a Tramex CME or CMExpert type concrete moisture meter. Sikalastic® Primer – For concrete decks with a maximum
PRODUCT DATA SHEET Sikaflex®-1A
usa.sika.comSpecification TT-S-00230C, Type II, Class A. Meets ASTM C-920, Type S, Grade NS, Class 35, use T, NT, O, M, G, I, A. Canadian standard CAN/CGSB 19.13-M87. USES Designed for all types of joints where maximum depth of sealant will not exceed 1/2 in. Excellent for small joints and fillets, windows, door
PRODUCT DATA SHEET Sika® FerroGard®-903
usa.sika.comreinforced, prestressed, precast, post tensioned or marine concrete. Use of Sika® FerroGard®-903: Steel-reinforced concrete, bridges and highways exposed to corrosive environments (deicing salts, weathering) Building facades and balconies Steel-reinforced concrete in or near a marine environment Parking garages
PRODUCT DATA SHEET Sikaflex®-1A
usa.sika.comJoint dimension should allow for 1/4 inch minimum and 1/2 inch maximum thickness for sealant. Proper design is 2:1 width to depth ratio, For use in horizontal joints in traffic areas, the absolute minimum depth of the sealant is 1/2 in. and closed cell backer rod is recommended. Removal Use personal protective equipment (chemical resistant
Related documents
SCIENCE CITATION INDEX EXPANDED - JOURNAL LIST …
bezmialem.edu.tr5. aatcc review 6. abdominal imaging 7. abhandlungen aus dem mathematischen seminar der universitat hamburg 8. abstract and applied analysis 9. abstracts of papers of the american chemical society 10. academic emergency medicine 11. academic medicine 12. academic pediatrics 13. academic radiology 14. accountability in research-policies and ...
AAMA 611-98 Voluntary Specification for Anodized ...
aluminium-guide.comAATCC - American Association of Textile Chemists and Colorists ASTM - American Society for Testing and Materials CMC - Color Measurement Committee of the Society of Dyers and Colorists ISO - International Organization for Standardization 5.0 GENERAL 5.1 To meet this specification, products tested shall meet all
Sto Gold Coat
www.stocorp.comAATCC 127 (modified) No cracking of the coating or bond failure, no water penetration after cyclic weathering & 5 hour water column (21.5 in [55 cm]) Pass Adhesion to ASTM E2570/C297 > 15 psi (103 kPa) > 15 psi (105 kPa) over glass mat gypsum sheathing > 50 psi (345 kPa) over CMU, OSB & plywood sheathing Air Leakage Resistance
Colorfastness to Light - Contract Textiles
contracttextiles.orgAATCC 16 Option 1 or 3* The AATCC 16 Option 1 and 3 are test methods of the American Association of Textile Chemists and Colorists (AATCC). ACT recognizes both methods where the only difference is the light source being used. In AATCC 16 Option 1 a Carbon-Arc lamp is used as the light source, and in AATCC 16 Option 3 a Xenon-Arc lamp is used.