LAB MANUAL for Computer Network
22 Configuring Static and Default Routes 23 Configuring RIP 24 Planning Network-based Firewalls 25 Configuring a Cisco Router as a DHCP Server. Experiment-1 Aim: Study of different types of Network cables and Practically implement the cross-wired cable and straight through cable using clamping tool.
Download LAB MANUAL for Computer Network
Information
Domain:
Source:
Link to this page:
Documents from same domain
CONCRETE BLOCK MASONRY
sjce.ac.inThe width of cavity is constant with a suitable value between 40 to 100 mm & cavity is continuous in vertical direction expect at lintel on openings. The inner & outer walls are interconnected by means of “metal ties” or “bonding bricks”. The bottom of cavity wall should be well-ventilated by use of air bricks and ducts.
GEOTECHNICAL ENGINEERING LABORATORY
sjce.ac.inA) Determination of liquid limit (Casagrande method) B) Determination of plastic limit C) Determination of shrinkage factors 11 5. Determination of liquid limit of fine-grained soils by fall cone method 19 6. Determination of in situ dry density A) Core cutter method B) Sand Replacement method 21 7. Free swell tests 27 Engineering Property ...
Heat and Mass Transfer Laboratory Manual
sjce.ac.inConduction is a process of heat transfer through solids, liquids and gases. When the temperature gradient exists in a body, experience has shown that there is a transfer of heat from high temperature region to the low temperature region. The heat transfer rate per unit is
ELEMENTS OF CIVIL ENGINEERING
sjce.ac.inThey work to reduce environmental pollution, increase the world’s food supply, and make transportation faster & safer. Out of all branches of engineering, Civil Engineering is the one that is directly associated with the welfare of the society. …
Digital Electronics Circuits
sjce.ac.inDigital Electronics Circuits (EC37L) Lab in-charge: Dr. Shankraiah Course outcomes: After the completion of laboratory the student will be able to, 1. Simplify, design and implement Boolean expression/half and full adders using basic/universal gates. 2. Design and implement the various combinational circuits using MSI components. 3.
Metrology and Measurement Laboratory Manual
sjce.ac.in2. Measurement of angle using Sine Center / Sine bar / bevel protractor 3. Measurement of alignment using Autocollimator / Roller set 4. Measurement of cutting tool forces using a) Lathe tool Dynamometer b) Drill tool Dynamometer. 5. Measurement of Screw threads Parameters using two wire or Three-wire methods. 6.
Foundry and Forging Laboratory Manual
sjce.ac.in01 Foundry -Introduction 37-39 02 Core and Core Making 40-50 03 Solid Pattern 50-51 04 Hand Cutting 52-54 05 Self-Cored Pattern 55-56 06 Stepped Cone Pulley with Core Print 57-57 07 Split Pattern with Two Halves 58-58 08 Split Pattern with Two Halves 59-64
REMOTE SENSING AND GIS APPLICATIONS
sjce.ac.inHISTORY OF REMOTE SENSING The invention of photography in 1839 made remote sensing (eventually) possible. Remote sensing began in the 1860s as balloonists took pictures of the Earth's surface. Pigeon fleets were another form of remote sensing in the early years.
Machine Shop Manual
sjce.ac.inCutting of Gear Teeth using Milling Machine. COURSE OUTCOMES: ... milling machines, grinding machines, power saws, and presses (e.g., punch presses). ... cemented carbides, ceramics, diamond & cubic boron nitride (CBN). Types of Tool Materials: High Carbon steels High Speed Steels Cemented Carbides
METHODS OF ANALYSIS FOR EARTHQUAKE RESISTANT …
sjce.ac.in4 Steel Moment Resisting Frame Designed as per SP 6(6) 5.0 Buildings with Shear Walls4 5 Load Bearing Masonry Wall Buildings5 a)Un-reinforced b)Reinforced with Horizontal RC Bands c)Reinforced with Horizontal RC Bands and Vertical bars At corners of rooms and jambs of openings 1.5 2.5 3.0 6 Ordinary Reinforced Concrete Shear Walls6 3.0
Related documents
Configuring IPsec VPN with a FortiGate and a Cisco ASA
community.cisco.comConfiguring the static route in the FortiGate. Navigate to Router > Static > Static . Routes and select Create New. Create a static route with the Destination . IP/Mask matching the address of the Cisco local network (by default, 192.168.1.0). Under . Device, select the site-to …
configuring static routes - Router Alley
routeralley.com- Configuring Static Routes - Configuring Static Routes The basic syntax for a static route is as follows: Router(config)# ip route [destination_network] [subnet_mask] [next-hop] Consider the following example: RouterA will have the 172.16.0.0/16 and 172.17.0.0/16 networks in its routing table as directly-connected routes. To add a static route ...
Basic Router Configuration - Cisco
www.cisco.com† Configuring Static Routes, page 23 ... The loopback interface acts as a placeholder for the static IP address and provides default routing information. For complete information on the loopback commands, see the Cisco IOS Release configuration guide documentation set.
Configuring Static and Default Routes - Cisco
www.cisco.comChapter 25 Configuring Static and Default Routes Configuring Static and Default Routes Examples The following example shows static rout es that are equal cost routes that direct traf fic to three different gateways on the outside interface. The ASA distributes the traffic among the specified gateways.
Cisco Business 250 Series Smart Switches Data Sheet
www.cisco.comUp to 32 static routes and up to 16 IP interfaces IPv6 routing Wire-speed routing of IPv6 packets Layer 3 interface Configuration of Layer 3 interface on physical port, LAG, VLAN interface, or loopback interface Classless Interdomain Routing (CIDR) Support for CIDR
Configuring the Grandstream UCM6200/UCM6300 for use …
www.exele.comto assign its default static IP address to both the WAN and LAN port. Once assigned you can connect the UCM6300 to your computer/laptop and use this static IP below. To enable the static IP address, from the LCD screen: o Home button (house icon) o …
SonicWall Switch Getting Started Guide
www.sonicwall.comSonicWall Switch Gettng Started Guide Overview 2 5 Overview • Introduction on page 5 • Hardware Overview on page 7 • About PoE on page 13 • About SFP/SFP+ on page 13 • Specifications on page 13 Introduction The SonicWall Switches are designed to connect SonicWall firewalls with Access Points and IP Surveillance
Related search queries
Configuring, FortiGate, Static, Routes, Default, Configuring Static Routes, Basic Router Configuration, Cisco, Configuring Static and Default Routes, Configuring Static and Default Routes Configuring Static and Default Routes, Static rout es, Static routes, Default static, SonicWall Switch Getting Started Guide, SonicWall