MODULE 1 - courses.ownerbuildercentre.com.au
Let’s begin by looking at what hazards and risks actually are. A hazard is an actual or potential source of injury, ill health or disease in the workplace. Hazards may include: • source or a situation with a potential for harm in terms of human injury or ill health • damage to property • damage to the environment
Download MODULE 1 - courses.ownerbuildercentre.com.au
Information
Domain:
Source:
Link to this page:
Documents from same domain
BUILDER’S GUIDE TO OHS
courses.ownerbuildercentre.com.auTimber / Steel framed houses As the name suggests, the main structural elements of these houses are built using timber or steel frames, though they are also built on a cavity structure consisting of two walls. The internal, wall framework is erected first and the outer wall is then built from brick, block or wood cladding.
MODULE 2 - courses.ownerbuildercentre.com.au
courses.ownerbuildercentre.com.auSite Plan The site plan shows an outline of a house in relation to north, neighbouring houses and the roads, ... Specifications describe the materials, installation techniques and quality standards for what is to be built. ... which ensures that the development proposal is broadly compatible with surrounding land uses. The
MODULE 3 - courses.ownerbuildercentre.com.au
courses.ownerbuildercentre.com.auThe model Code of Practice for Construction Work provides practical guidance to achieve the standards of health, safety and welfare required under the model WHS Act and Regulations in relation to construction work. High risk construction work In the construction industry, a PCBU that carries out high risk construction has additional WHS duties.
0171 General Requirements
courses.ownerbuildercentre.com.au0171 General Requirements Specification 3 September 2017, Version 7.0 0511 Linings ..... 155
PROJECT ASSESSMENT
courses.ownerbuildercentre.com.auList and briefly describe at least ten (10) sub-tasks that make up the whole Work Task – the sub-tasks must be listed in a logical order to maximise efficient use of resources List the Trades that are needed for each sub-task (minimum of three people, including yourself – e.g: …
PROJECT NAME Kitchen and Bathroom refurbishment, and …
courses.ownerbuildercentre.com.auTimber Deck Planks Materials for piers, concrete footings and steel frame Kango Hammer / Sledge Hammer Blow Torch Chisel / Crow Bar Drill / Screw Drivers ... gas piping in preparation for the installation of the new Kitchen Sink, Dishwasher and Oven / Stove Plumber Electrician Blow torch Chisel Drill Screw Driver
Section 1: Identification of the Material and Supplier
courses.ownerbuildercentre.com.auSAFETY DATA SHEET Concrete Mix Section 1: Identification of the Material and Supplier Company Details Cement Australia Pty Limited ABN 75 104 053 474 18 Station Avenue Darra, Queensland 4076 Tel: 1300 CEMENT (1300 236 368) Fax: 1800 CEMENT (1800 236 368) Website: www.cementaustralia.com.au Emergency Contact Number: Contact Person: …
Related documents
4.3 Hazard Identification, Risk Assessment and Risk ...
studentsrepo.um.edu.myaccess the risk or postulate solutions where the identification of hazards should involve a critical appraisal of all activities. A similar problem is that OHSMS tend to focus upon easily identified hazards such as ‘trips and falls’ rather than the identification of potential major hazards (Hopkins, 2000; Walker, 1998).
MEDICAL SURVEILLANCE PROGRAM
www.ehs.wvu.eduinhalation, ingestion, skin contact or absorption, past exposure. Employee Exposure Measurements - For chemical hazards or physical hazards that are measured for the employee that include: Air Contaminants exposure measurements are employee breathing zone measurements during an employee’s normal workday and other working conditions as well.
OSHA 3221-12N 2004
www.osha.govchemical hazards and hazardous sub-stances, reporting of hazards, appropriate personal protective equipment and what to do in emergency situations. Train workers in safe work practices and methods for all work activities, proce-dures and equipment as well as how to recognize and respond to potential work-place hazards, including rendering first ...
750 Introduction to Industrial Hygiene
www.oshatrain.orgenvironmental and physical hazards that can affect the health and well-being of workers. Important IH responsibilities include: • Identifying, measuring and analyzing workplace health hazards and exposures (chemical, physical, biological, ergonomic) that can cause sickness, impaired health, or significant discomfort.