OPERATOR'S MANUAL - Baldor
♦Place protective covers and guards over the rotating parts, if rotating parts such as the drive shaft, pulley, belt, etc. are left exposed, they are potentially hazardous.
Download OPERATOR'S MANUAL - Baldor
Information
Domain:
Source:
Link to this page:
Documents from same domain
Baldor Electric Company Premium Efficiency Motor ...
www.baldor.com3.2.2 Enclosures shall be rolled steel band or cast iron construction depending on horsepower. End brackets shall be die cast aluminum with steel bearing inserts or cast iron construction.
NEMA QUICK REFERENCE CHART - Home - …
www.baldor.comnema quick reference chart nema frame de2f h nop uvaa ab ah aj ak ba bb bd xo tap 42 2-5/8 1-3/4 1-11/16 9/32 1-1/2 54-11/163/8 1-1/8 3/84-1/32 1 …
SERVO CONTROL FACTS - Baldor.com
www.baldor.comPage 3 Servo Control Facts TYPES OF MOTORS The direct current (DC) motor is one of the first machines devised to convert electrical energy to mechanical power.
Multipurpose Brake - Home - Baldor.com
www.baldor.comMN802 Table of Contents i ... Control Wiring Diagrams ... The Multipurpose Brake verifies that the DC contactor ...
Capabilities in the Oil & Gas Industry - Baldor.com
www.baldor.comQuality is what we do everyday because customers need equipment that runs safely and reliably throughout the lifecycle Our products are designed to operate in the oil and gas industry in extreme conditions from desert to arctic, onshore and
MN715 15H Inverter - Baldor.com
www.baldor.comSection 1 Quick Start Guide MN715 Quick Start Guide 1-1 Overview If you are an experienced user of Baldor controls, you are probably already familiar with the keypad programming and keypad operation methods.
SPECIFIER GUIDE INTRODUCTION - Baldor Electric …
www.baldor.compower source and the electric motor, the single phase motors are rated either 115 volt or 230 volt. Three phase motors are rated 200 volt, 230 volt, 460 volt and 575 volt.
NEMA QUICK REFERENCE CHART - Baldor.com
www.baldor.comnema quick reference chart nema frame de2f h nop uvaa ab ah aj ak ba bb bd xo tap 42 2-5/8 1-3/4 1-11/16 9/32 1-1/2 54-11/163/8 1-1/8 3/84-1/32 1-5/16 3 …
EG21 and EGS21 Series Electric Gage and …
www.baldor.comEG21 and EGS21 Series Electric Gage and SWICHGAGE® Installation For Pressure, Temperature, Fuel Level, Voltmeter and Ammeter EG21-96048N Revised 03-99 Section 70
MicroFlex Servo Control - Baldor.com
www.baldor.comMN1919 General Information 1-3 WARNING: The stop input to this equipment should not be used as the single means of achieving a safety critical stop. Drive disable, motor disconnect, motor brake and other means should be used as appropriate. WARNING: Improper operation or programming of the drive may cause violent motion of the motor …
Related documents
Preventing high voltage electric contact accidents …
gravitymagnet.comThe minimum approach distance is intended to: Provide a sufficient gap between the worker and the energized line or equipment so that current cannot arc to the employee under the most adverse transient voltages that could be
Working on Exposed Energized Parts
keystoneinsulatorcleaner.comunder normal conditions, of dangerous approach or accidental contact by persons or objects. NOTE: Wires which are insulated, but not …
Agreement - UNECE
www.unece.orgGE.11- Agreement Concerning the adoption of uniform technical prescriptions for wheeled vehicles, equipment and parts which can be fitted and/or be used on
Arc Flash Hazard Design, Maintenance and …
www.wmea.net2 ©2004 Electrical Reliability Services, Inc. Arc Flash Hazard Design, Maintenance and Operation Process Checklist Yes No Don’t Know 2-1 Operations 2-1.2 Training 2-1.2.3 Is there a process in place that ensures the training program is periodically reviewed to identify needed changes?
Understanding “Arc Flash”
www.osha.govThis material was produced under grant number SH-16615-07-60-F-12 from the Occupational Safety and Health Administration, U.S. Department of Labor.