Packaging Information - Vishay Intertechnology
77 P DFS bridge, 16 mm tape, 13" diameter paper reel 80 P MB-S (TO-269AA) bridge, 12 mm tape, 13" diameter paper reel 81 P D2PAK (TO-263AB) 24 mm tape, 13" diameter reinforced hub plastic reel 8W P D2PAK (TO-263AB) (wire bond) 24 mm tape, 13" diameter reinforced hub plastic reel 83 P GL34 (DO-213AA) 8 mm tape, 13" diameter plastic reel
Download Packaging Information - Vishay Intertechnology
Information
Domain:
Source:
Link to this page:
Documents from same domain
How to Select the Right MOSFET for Power Factor …
www.vishay.comVISHAY SILICONIX Power MOSFETs Application Note - AN844 How to Select the Right MOSFET for Power Factor Correction Applications APPLICATION NOTE Revision: 03-Jun-13 1 Document Number: 65677
Automotive P-Channel 60 V (D-S) 175 °C MOSFET
www.vishay.comSQ7415AEN www.vishay.com Vishay Siliconix S13-1891, Rev. C, 26-Aug-13 1 Document Number: 67042 For technical questions, contact: automostechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
Transient Voltage Suppressors (TVS) for …
www.vishay.comTransient Voltage Suppressors (TVS) for Automotive Electronic Protection www.vishay.com For technical questions within your region, please contact one of the following: Document Number: 88490
Power Metal Strip Resistors, Low Value (down to …
www.vishay.comWSR High Power www.vishay.com Vishay Dale Revision: 11-Jul-2018 1 Document Number: 31059 For technical questions, contact: ww2bresistors@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
Resistive Products Power Dissipation in High …
www.vishay.comDocument Number: 53048 www.vishay.com Revision: 29-Oct-09 1 VISHAY SFERNICE Resistive Products Application Note Power Dissipation in High Precision Vishay Sfernice Chip Resistors and Arrays
Vishay Semiconductors
www.vishay.comVCUT0505B-HD1 www.vishay.com Vishay Semiconductors Rev. 2.2, 16-May-17 1 Document Number: 81852 For technical questions, contact: ESDprotection@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
RF PIN Diodes - Single in DO-35 (DO-204AH) - Vishay
www.vishay.comLegal Disclaimer Notice www.vishay.com Vishay Revision: 08-Feb-17 1 Document Number: 91000 Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
Small Signal Switching Diodes, High Voltage
www.vishay.comBAV17, BAV18, BAV19, BAV20, BAV21 www.vishay.com Vishay Semiconductors Rev. 1.9, 12-Jul-17 3 Document Number: 85543 For technical questions within your region ...
High Precision Wraparound - Wide Ohmic Value …
www.vishay.comP www.vishay.com Vishay Sfernice Revision: 23-Feb-18 1 Document Number: 53017 For technical questions, contact: sferthinfilm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
Aluminum Electrolytic Capacitors Radial Standard …
www.vishay.com038 RSU www.vishay.com Vishay BCcomponents Revision: 28-Feb-17 1 Document Number: 28309 For technical questions, contact: aluminumcaps1@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
Related documents
Using the Three-Wire Method to Measure Threads
littlemachineshop.comDiameter for pitch-line contact = 0.57735 × Pitch If you do the math, you will find that all the suggested wires in the table above are between the smallest and largest values. ©2011 LittleMachineShop.com Page 4 of 4 The thread pitch for an American National Standard Unified 60 …
Shaft Stress Calculations - Rochester Institute of Technology
edge.rit.edud= .833” – Pitch diameter o F= .25” – face width o K m = 1.20 – Load-Distribution factor, based on geometry o K B = 1 – Rim Thickness factor, based on geometry o J= .325- Geometry factor, based on number of teeth of gears o J K K F P W K K K d m B o v s t =5357.1 psi o max n S y = 9.0 Endurance Stress o 1/ 2 2 2) 1 1 (1 G G p p p E ...
STAIRS Design & Construction - Weebly
piaresearch.weebly.comhandrail: A rail fixed parallel above the pitch line at the sides of a stair. balusters: Vertical members which support a handrail. Newel: A vertical post which might provide support for either the handrail, or support for the upper end of an outer string.
Flange dimension guide - Reece
www.reece.com.auDiameter Pitch Circle Diameter No. Holes Hole Diameter Bolt Diameter Minimum Flange Thickness Cast Iron Ductile Iron Copper Alloy Steel AS 4087 PN14 150 114 4 18 M16 - - 10 - PN16 150 114 4 18 M16 - - - 11 PN21 165 127 4 18 M16 - - - 15 PN35 165 127 4 18 M16 - - - 19 Drilling for AS 4087 Class PN14 & PN16 is compatible with AS 2129, Table D