Plaster Systems Brochure (English) - SA920 - USG
–5/89 panel can be substituted for 5/8 i9mpeRial Brand FiRecoDe Core Gypsum Base and certain 1/2 9impeRial Brand FiRecoDe C Core Gypsum Base in wall assemblies without compromising the fire rating (see Application Guide Specifications, Part 3.3.5) – Refer to product submittal sheet F218 for more information impeRial® Brand Gypsum Base
Download Plaster Systems Brochure (English) - SA920 - USG
Information
Domain:
Source:
Link to this page:
Documents from same domain
USG Fire-Resistant Assemblies Catalog (English) - …
www.usg.com4 USG Fire-Resistant Assemblies Fire Protection USG is the undisputed leader among building material manufacturers in providing products and systems designed to keep people safe from fire.
USG Area Separation Wall Systems Brochure …
www.usg.comArea separation walls between adjoining townhouses must provide fire-resistive ratings to ensure the safety of occupants in adjacent dwellings.
Fire-Resistant Assemblies Brochure (English) - SA100
www.usg.comUser’s Guide Use this brochure to determine fire ratings for CGC products and systems. This brochure provides: — Comprehensive information about fire-rated assemblies
Technical Document Seismic Technical Guide - USG
www.usg.com4 Hanger Wire Attachment Application Anchorage The International Building Code (IBC), through references to ASCE/SEI 7 Minimum Design Loads for Buildings and Other Structures, American Society of Civil Engineers/Structural Engineering Institute (ASCE/SEI), defines
Technical Document Seismic Technical Guide - USG
www.usg.comTechnical Seismic Technical Guide Document Light Duty Suspension Systems ASTM C6351 addresses the load carrying capability of main tees, categorizing them as Light, Intermediate or Heavy Duty.
CGC SHAFT WALL SYSTEMS - USG
www.usg.comC-H studs in a progressive manner, with gypsum panels, gypsum fiber panels or cement board applied to the face. All details, specifications and data contained in this literature are intended as a …
USG DUROCK BRAND CEMENT BOARD SYSTEMS
www.usg.comSTANDARDS USG Durock® cement board exceeds ANSI standards for cementitious backer units (CBU). See ANSI A118.9 for test See ANSI A118.9 for test methods and specifications for CBU and ANSI A108.11 for interior installation of CBU.
Manual Técnico USG Tablaroca® (Español)
www.usg.comUSG Manual Técnico USG TABLAROCA® USG SHEETROCK® Manejo, almacenaje, especificación, instalación y recomendaciones generales.
0 ICC-ES Evaluation Report ESR-1222 - USG
www.usg.comThe USG suspended ceiling framing systems described in this report are suspended, exposed framing, concealed ceiling assemblies used in fire-rated and non -resistance -
Technical Document Seismic Technical Guide - USG
www.usg.comTechnical Seismic Technical Guide Document Compression Posts USG Donn® Brand Compression Post providesidrig support for a ceiling suspension system in seismic applications. Telescoping compression posts attach to the main tees at each splayed wire location, preventing upward
Related documents
Steel Framing Guide
www.steelframing.orgwall types are correctly marked, fire-rated assemblies, if required are shown, details are provided for key connections, and mechanical, electrical and plumbing drawings are coordinated with the structural drawings. 3. Structural drawings will be reviewed for consistency with the architectural drawings, and to ensure that specific
IS 811 (1987): Cold Formed Light Gauge Structural Steel ...
law.resource.orgwall* panels); and c) Where sub-assemblies of such members may be pre-fabricated in the plant, reducing site erection to a minimum of simple operations. 0.4 It is not intended that the freedom of designers and/or manufacturers should be limited to …
Architectural Woodwork Standards doors 9
woodworkinstitute.comsection 9 Doors 236Architectural Woodwork Standards ©2014 AWI | AWMAC | WI 2nd Edition, October 1, 2014 9 table of contents coMplIAnce requIreMents (continued) product (continued) Material Rules (continued)
FireMaster FastWrap XL - Morgan Thermal Ceramics
www.morganthermalceramics.comthe access panel, and impaled over the insulation pins on the panel. A second layer of FastWrap XL is cut so as to overlap the first layer a minimum of 1-1/2” (38mm). It is essential that the first and second layer fit tightly against the surrounding wrap with no through openings. The third and outside layer should be cut to overlap the
Fire Resistance Ratings - UL 263
www.thco.isFire resistance assemblies and products are developed by the design submitter and have been investigated by UL for compliance with ... Nonbearing Wall Ratings — 1, 1-1/2, 2 or 3 Hr (See Item 4) ... (Item 5) prior to panel installation. Nominal 10mm thick panels installed vertically with vertical joints centered over studs and staggered from ...