Prescriptive Residential Wood Deck Construction Guide
American Wood Council 11. Flashing shall be corrosion-resistant metal [R703.8] of minimum nominal 0.019-inch thickness or approved non-metallic material. Aluminum should not be used in direct contact with lumber treated with preservatives that contain copper such as ACQ, Copper Azole, or ACZA. 12. Decks shall not be used or occupied until final
Download Prescriptive Residential Wood Deck Construction Guide
Information
Domain:
Source:
Link to this page:
Documents from same domain
INTERIOR SHEAR WALLS - awc.org
www.awc.orginterior shear walls to be designed to resist wind loads. WFCM Section 2.4.4.2 states: “Walls parallel to the applicable wind load or seismic motion shall provide the required shear resistance at each level. The sum of the individual shearwall segment shear
2012 ASD/LRFD Manual for Engineered Wood Construction
www.awc.orgASD/LRFD MANUAL FOR ENGINEERED WOOD CONSTRUCTION iii AMERICAN WOOD COUNCIL FOREWORD This Allowable Stress Design/Load and Resistance Factor Design Manual for Engineered Wood Construction (ASD/LRFD Manual) provides guidance for design of most wood-based structural products used in the construction
2015 National Design Specification Supplement - awc.org
www.awc.orgAMERICAN WD CUNCIL. DESIGN VALUES FOR WOOD CONSTRUCTION – NDS SUPPLEMENT iii. Introduction. This Supplement is a compendium of reference de …
2005 Span Tables For Joists And Rafters - awc.org
www.awc.org2 EXPLANATION OF TABLES AMERICAN WOOD COUNCIL 7. LUMBER IDENTIFICATION The tabulated spans in these tables apply to lum-ber identified by the grade stamp of, or certificate of
Design Aid 6 Beam Design Formulas with Shear and Moment ...
www.awc.orgAMERICAN WOOD COUNCIL w R V V 2 2 Shear M max Moment x 7-36 A ab c x R 1 R 2 V 1 V 2 Shear a + — R 1 w M max Moment wb 7-36 B Figure 1 Simple Beam–Uniformly Distributed Load
WIND & SEISMIC - AWC
www.awc.org2.1.2.1 Allowable Stress Design: Allowable stress design (ASD) shall be in accordance with the Na-tional Design Specification ® (NDS ®) for Wood Con-struction (ANSI/AF&PA NDS-05) and provisions of this document. 2.1.2.2 Strength Design: Load and resistance factor design (LRFD) of wood structures shall be in accor-
WCD1 - Details for Conventional Wood Frame Construction
www.awc.orgmay provide equal, or possibly, improved performance. These, however, must provide performance assurance ac-ceptable to the owner and the building inspector. Dimensioning. In general, dimensions for framing lumber, wood sid-ing and trim referenced in this document are nominal dimensions; i.e., 2x4, 2x6, etc., for simplicity. Actual sur-
Prescriptive Residential Wood Deck Construction Guide
www.awc.org3. Maximum allowable overhang cannot exceed L/4 or ¼ of actual main span. Assumes cantilever length/180 deflection with 220 lb point load (See Figure 1A and Figure 2). 4. Incising assumed for Douglas Fir-Larch, Hem-Fir, and Spruce-Pine-Fir. 5. Design values based on northern species with no incising assumed. 6. Ledger shall be a minimum of 2x8 ...
2015 National Design Specification - AWC
www.awc.orgNDS-1991 with an approval date of October 16, 1992. In 2010, AWC was separately incorporated, re-chartered, and accredited by ANSI as a standards developing organization. The current edition of the Standard is designated ANSI/AWC NDS-2015 with an approval date of September 30, 2014. In developing the provisions of this Specification,
MAT100: The Basics of Wood Frame Construction
www.awc.orgone comprehensive program for building officials on wood frame construction basics. In each module, learning outcomes will be further refined respectively. MAT 100 learning outcomes (see slide). 5 MAT100: Learning Outcomes 3. Floor, roof/ceiling, wall framing 4. Wall bracing, introduction to Wood Frame Construction Manual 5. Fireblocking ...
Related documents
Chapter 9: Column Analysis and Design
academic.csuohio.eduVirtually every common construction material is used for column construction. • Steel, timber, concrete (reinforced and pre-stressed), and masonry (brick, block, and stone). The selection of a particular material may be made based on the following. • Strength (material) properties (e.g. steel vs. wood).
U.S. Technical Guide
lpcorp.com3. For beams bearing on wood plates, the required bearing length will increase based on the bearing strength (compression perpendicular-to-grain) of the species and grade used for the plate material. 4. Verify local code requirements concerning minimum bearing. FASTENERS:
A partial list of products made from Petroleum (6000 items)
whgbetc.comAsphalt used in road construction is a petroleum product as is the synthetic rubber in the tires. Paraffin wax comes from petroleum, as do fertilizer, pesticides, herbicides, detergents, phonograph records, photographic film, furniture, packaging materials, surfboards, paints, and artificial fibers used in clothing, upholstery, and carpet backing.
Tree species used in historical shipbuilding and their ...
deguwa.orgresistant timbers or effective wood protection ‒ either on a chemical basis or by means of structural measures. According to DIN EN 350-2 (durability of wood and wood products ‒ natural durability of solid wood), Basralocus and Greenheart are considered durable; Bilinga, Bongossi/Azobe, Sapeli, and Teak are seen as moderately durable.
Construction and Building Contractors - California
www.cdtfa.ca.goved Wood Products : For More Information ; 34 : Section : Page : Defnition of Terms : Construction contracts : A construction contract is a contract, whether on a lump sum, time and material plus tax, cost-plus a fee, or other basis, to: 1. Erect, construct, alter, or repair any building or other structure, project, development, or other
Build a duck nest box - Ducks Unlimited
www.ducks.orgWood ducks, Barrow’s goldeneyes, common goldeneyes, hooded mergansers, common mergansers and buffleheads are all cavity nesting ducks. They build nests in abandoned woodpecker holes ... which is used by the Ducks Unlimited Greenwing program, may even attract other cavity nesting birds such as kestrels, tree swallows, great crested ...
Appendix C Materials Used in Aircraft
www.fire.tc.faa.govOther types of core materials that have been used include polyurethane, polyvinyl chloride, polyimide foams (to reinforce edges and fastener points), and balsa wood (for floor panels in passenger cabins and cargo holds). C.4.3 Adhesives for Bonding Face Sheets to Core Epoxy and modified phenolic film adhesives are used to bond face sheets to ...
Wood Destroying Insect Inspection Report
www.hud.govreinfesting wood boring beetles. This inspection does not include mold, mildew or noninsect wood destroying organisms. This report shall be considered invalid for purposes of securing a mortgage and/or settlement of property transfer if not used within ninety (90) days from the date of inspection. This shall not be construed as a 90-day warranty .