Prescriptive Residential Wood Deck Construction Guide
PRESCRIPTIVE RESIDENTIAL WOOD DECK CONSTRUCTION GUIDE 3 American Wood Council 11. Flashing shall be corrosion-resistant metal [R703.8] of minimum nominal 0.019-inch thickness or approved non-metallic material. Aluminum should …
Download Prescriptive Residential Wood Deck Construction Guide
Information
Domain:
Source:
Link to this page:
Documents from same domain
INTERIOR SHEAR WALLS - awc.org
www.awc.orginterior shear walls to be designed to resist wind loads. WFCM Section 2.4.4.2 states: “Walls parallel to the applicable wind load or seismic motion shall provide the required shear resistance at each level. The sum of the individual shearwall segment shear
2012 ASD/LRFD Manual for Engineered Wood Construction
www.awc.orgASD/LRFD MANUAL FOR ENGINEERED WOOD CONSTRUCTION iii AMERICAN WOOD COUNCIL FOREWORD This Allowable Stress Design/Load and Resistance Factor Design Manual for Engineered Wood Construction (ASD/LRFD Manual) provides guidance for design of most wood-based structural products used in the construction
2015 National Design Specification Supplement - awc.org
www.awc.orgAMERICAN WD CUNCIL. DESIGN VALUES FOR WOOD CONSTRUCTION – NDS SUPPLEMENT iii. Introduction. This Supplement is a compendium of reference de …
2005 Span Tables For Joists And Rafters - awc.org
www.awc.org2 EXPLANATION OF TABLES AMERICAN WOOD COUNCIL 7. LUMBER IDENTIFICATION The tabulated spans in these tables apply to lum-ber identified by the grade stamp of, or certificate of
Design Aid 6 Beam Design Formulas with Shear and Moment ...
www.awc.orgAMERICAN WOOD COUNCIL w R V V 2 2 Shear M max Moment x 7-36 A ab c x R 1 R 2 V 1 V 2 Shear a + — R 1 w M max Moment wb 7-36 B Figure 1 Simple Beam–Uniformly Distributed Load
WIND & SEISMIC - AWC
www.awc.org2.1.2.1 Allowable Stress Design: Allowable stress design (ASD) shall be in accordance with the Na-tional Design Specification ® (NDS ®) for Wood Con-struction (ANSI/AF&PA NDS-05) and provisions of this document. 2.1.2.2 Strength Design: Load and resistance factor design (LRFD) of wood structures shall be in accor-
WCD1 - Details for Conventional Wood Frame Construction
www.awc.orgmay provide equal, or possibly, improved performance. These, however, must provide performance assurance ac-ceptable to the owner and the building inspector. Dimensioning. In general, dimensions for framing lumber, wood sid-ing and trim referenced in this document are nominal dimensions; i.e., 2x4, 2x6, etc., for simplicity. Actual sur-
Prescriptive Residential Wood Deck Construction Guide
www.awc.org3. Maximum allowable overhang cannot exceed L/4 or ¼ of actual main span. Assumes cantilever length/180 deflection with 220 lb point load (See Figure 1A and Figure 2). 4. Incising assumed for Douglas Fir-Larch, Hem-Fir, and Spruce-Pine-Fir. 5. Design values based on northern species with no incising assumed. 6. Ledger shall be a minimum of 2x8 ...
2015 National Design Specification - AWC
www.awc.orgNDS-1991 with an approval date of October 16, 1992. In 2010, AWC was separately incorporated, re-chartered, and accredited by ANSI as a standards developing organization. The current edition of the Standard is designated ANSI/AWC NDS-2015 with an approval date of September 30, 2014. In developing the provisions of this Specification,
MAT100: The Basics of Wood Frame Construction
www.awc.orgone comprehensive program for building officials on wood frame construction basics. In each module, learning outcomes will be further refined respectively. MAT 100 learning outcomes (see slide). 5 MAT100: Learning Outcomes 3. Floor, roof/ceiling, wall framing 4. Wall bracing, introduction to Wood Frame Construction Manual 5. Fireblocking ...
Related documents
Required number of 16d common nails per connection, wood
dpw.lacounty.govmaterial, except if the minimum total length of braced wall panel in the Table is multiplied by a factor of 1.5. d. WSP = 15/32” minimum thickness wood structural panel with 8d common (2 1/2” x 0.131) nails at 6” spacing (panel edge) at 12” spacing …
Frequently Asked Questions on Wood Packaging Materials
www.cbp.govmaterial” (SWPM). Wood packaging material is defined as wood or wood products (excluding paper products) used for supporting, protecting, or carrying cargo, including, but not limited to, dunnage, crating, pallets, packing blocks, drums, cases, or skids. The definition excludes manufactured wood materials, loose wood packing materials, and ...
Wood Handbook--Chapter 4--Mechanical Properties of Wood
www.fpl.fs.fed.usmaterials. Because wood is a natural material and the tree is subject to many constantly changing influences (such as moisture, soil conditions, and growing space), wood proper-ties vary considerably, even in clear material. This chapter provides information, where possible, on the nature and magnitude of variability in properties.
Wood Handbook, Chapter 04: Moisture Relations and Physical ...
www.fpl.fs.fed.usexchange between wood and air depends on the relative hu-midity and temperature of the air and the current amount of water in the wood. This moisture relationship has an impor-tant influence on wood properties and performance. Many of the challenges of using wood as an engineering material arise from changes in moisture content or an abundance of
Tax Credit - HPBA
www.hpba.orgThe wood heater burns biomass as a fuel, heats air or water, and is at least 75 percent efficient per the higher heating value (HHV) of the fuel Both purchase and installation costs (venting and related materials; onsite labor) can be included in your total cost A New Tax Credit for Modern Wood & Pellet Heat
Explanatory document for ISPM 15 Regulation of wood ...
www.ippc.intFeb 10, 2017 · wood packaging material, which is known as an important pathway in the movement of quarantine pests. ISPM 15 sets out harmonized requirements for the application of treatments to render wood packaging material practically free of quarantine pests. ISPM 15 also describes the use of an internationally
Regulation of wood packaging material in international trade
www.ippc.intFeb 01, 2019 · Wood packaging material covered by this standard includes dunnage but excludes wood packaging made from wood processed in such a way that it is free from pests (e.g. plywood). The phytosanitary measures described in this standard are not intended to provide ongoing protection