Prescriptive Residential Wood Deck Construction Guide
on ½" diameter fasteners. If larger (or smaller) fasteners are specified, edge distance and spacing shall be adjusted. 7. To resist corrosion, the following is required [R317.3]: All screws, bolts, washers, nuts, and nails for use with preservative treated wood shall be hot-dipped zinc-coated galvanized steel, stainless steel, silicon
Download Prescriptive Residential Wood Deck Construction Guide
Information
Domain:
Source:
Link to this page:
Documents from same domain
INTERIOR SHEAR WALLS - awc.org
www.awc.orginterior shear walls to be designed to resist wind loads. WFCM Section 2.4.4.2 states: “Walls parallel to the applicable wind load or seismic motion shall provide the required shear resistance at each level. The sum of the individual shearwall segment shear
2012 ASD/LRFD Manual for Engineered Wood Construction
www.awc.orgASD/LRFD MANUAL FOR ENGINEERED WOOD CONSTRUCTION iii AMERICAN WOOD COUNCIL FOREWORD This Allowable Stress Design/Load and Resistance Factor Design Manual for Engineered Wood Construction (ASD/LRFD Manual) provides guidance for design of most wood-based structural products used in the construction
Prescriptive Residential Wood Deck Construction Guide
www.awc.org4 PRESCRIPTIVE RESIDENTIAL WOOD DECK CONSTRUCTION GUIDE American Wood Council Table 2. Maximum Joist Spans and Overhangs.1 Species Size Joist Spacing (o.c.)
2015 National Design Specification Supplement - awc.org
www.awc.orgAMERICAN WD CUNCIL. DESIGN VALUES FOR WOOD CONSTRUCTION – NDS SUPPLEMENT iii. Introduction. This Supplement is a compendium of reference de …
2005 Span Tables For Joists And Rafters - awc.org
www.awc.org2 EXPLANATION OF TABLES AMERICAN WOOD COUNCIL 7. LUMBER IDENTIFICATION The tabulated spans in these tables apply to lum-ber identified by the grade stamp of, or certificate of
Design Aid 6 Beam Design Formulas with Shear and Moment ...
www.awc.orgAMERICAN WOOD COUNCIL w R V V 2 2 Shear M max Moment x 7-36 A ab c x R 1 R 2 V 1 V 2 Shear a + — R 1 w M max Moment wb 7-36 B Figure 1 Simple Beam–Uniformly Distributed Load
WIND & SEISMIC - AWC
www.awc.org2.1.2.1 Allowable Stress Design: Allowable stress design (ASD) shall be in accordance with the Na-tional Design Specification ® (NDS ®) for Wood Con-struction (ANSI/AF&PA NDS-05) and provisions of this document. 2.1.2.2 Strength Design: Load and resistance factor design (LRFD) of wood structures shall be in accor-
WCD1 - Details for Conventional Wood Frame Construction
www.awc.orgmay provide equal, or possibly, improved performance. These, however, must provide performance assurance ac-ceptable to the owner and the building inspector. Dimensioning. In general, dimensions for framing lumber, wood sid-ing and trim referenced in this document are nominal dimensions; i.e., 2x4, 2x6, etc., for simplicity. Actual sur-
2015 National Design Specification - AWC
www.awc.orgNDS-1991 with an approval date of October 16, 1992. In 2010, AWC was separately incorporated, re-chartered, and accredited by ANSI as a standards developing organization. The current edition of the Standard is designated ANSI/AWC NDS-2015 with an approval date of September 30, 2014. In developing the provisions of this Specification,
MAT100: The Basics of Wood Frame Construction
www.awc.orgone comprehensive program for building officials on wood frame construction basics. In each module, learning outcomes will be further refined respectively. MAT 100 learning outcomes (see slide). 5 MAT100: Learning Outcomes 3. Floor, roof/ceiling, wall framing 4. Wall bracing, introduction to Wood Frame Construction Manual 5. Fireblocking ...
Related documents
Business Ethics and Compliance
globalassets.starbucks.comThe Standards of Business Conduct support the Global Business Ethics Policy and provide an overview of some of the legal and ethical standards we are each expected to follow every day. If you are unsure of what to do in a situation, you have support. Speak with your manager, Partner Resources or Business Ethics and Compliance about your concerns.
WHISTLEBLOWERS ARE PROTECTED
www.dir.ca.govThe Division of Labor Standards Enforcement believes that the sample posting below meets the requirements of Labor Code Section 1102.8(a). This document must be printed to 8.5 x 14 inch paper with margins no larger than one-half inch in order to conform to the statutory requirement that the lettering be larger than size 14 point type.
Language Arts Florida Standards (LAFS) Grade K
www.fldoe.orgStrand: STANDARDS FOR SPEAKING AND LISTENING Cluster 1: Comprehension and Collaboration STANDARD CODE STANDARD. LAFS.K.SL.1.1 Participate in collaborative conversations with diverse partners about . kindergarten topics. and texts with peers and adults in small and larger groups. a. Follow agreed-upon rules for discussions (e.g., listening to ...
CODE OF CONDUCT AND ETHICS - Infosys
www.infosys.comOur Code, however, cannot possibly address every situation we ... both within the industry and within the larger society – but most of all, we are known for our values. These values, embodied in C-LIFE (Client Value, ... To set standards in our business and transactions and be an exemplar for the industry and ourselves.
National Code of Ethics for Interpreters in Health Care
www.ncihc.orgA National Code of Ethics for Interpreters in Health Care • July 2004 • Page 4 of 23 Understanding the National Code of Ethics for Interpreters in Health Care “The role of interpreter is a ‘tightrope’ balancing act: A code of ethics is a good guide for the ‘bar’ carried on such a walk on the tightrope.