Reported by Committee 302 - American Concrete Institute
slabs-on-ground, ACI 223R for shrinkage-compensating concrete floors, and ACI 421.1R and 421.2R for suspended floors. 5.2—Slabs-on-ground 5.2.1 Required design elements—Following are the minimum items that should be addressed in the construction documents prepared by the designer (ACI 360R): a) Slab-on-ground design criteria
Download Reported by Committee 302 - American Concrete Institute
Information
Domain:
Source:
Link to this page:
Documents from same domain
Flatwork Finisher Work Experience Form
www.concrete.orgwork experience and other background relevant to the stated requirement of the ACI certification programs. I agree to release and hold harmless any individual, company or institution, including the ACI, and any persons connected therewith from liability imposed by law in
LETTER FROM THE EDITOR-IN-CHIEF - concrete.org
www.concrete.org4 ACI Materials Journal/January 2018 ACI is an international leader in advancing the profession through dissemination of knowledge on concrete.
Concrete The Reinforced Design Manual
www.concrete.orgThe Reinforced Design Manual Concrete In Accordance with ACI 318-11. ACI SP-17(11) Volume 2 THE REINFORCED CONCRETE DESIGN MANUAL in Accordance with ACI 318-11 Anchoring to concrete ... with the design provisions of ACI 318-11, and is …
ACI 318-14 - American Concrete Institute
www.concrete.orgDraft Table of Contents Building Code Requirements for Structural Concrete and Commentary ACI 318-14. BUILDING CODE REQUIREMENTS FOR STRUCTURAL CONCRETE (ACI 318‐14) Chapter 1—General 1.1—Scope of ACI 318 ... 4.3—Design loads ...
Guide to Hot Weather Concreting - American Concrete Institute
www.concrete.orgGuide to Hot Weather Concreting. Guide to Hot Weather Concreting First Printing ... concrete materials. This guide provides measures that can be taken to ... curing hydraulic-cement concrete that adversely affect the properties and serviceability of the concrete. Most of these
308R-16: Guide to External Curing of Concrete
www.concrete.orgThis guide reviews and describes practices, procedures, materials, and monitoring methods for the external curing of concrete and provides guidance for specifying curing procedures.
ACI 117-10 Specification for Tolerances for Concrete ...
www.concrete.orgcommentary is not a part of ACI Specification 117-10. Specification for Tolerances for Concrete Construction and Materials (ACI 117-10) and Commentary ... Construction techniques—The feasibility of a tolerance depends on available craftsmanship, technology, materials, ... ACI 117-10 Specification for Tolerances for Concrete Construction and ...
ACI 318-11 to ACI 318-14 and ACI 318.2-14 Building Code ...
www.concrete.orgTransition Key: 318‐11 to 318‐14 Building Code Requirements for Structural Concrete 318‐11 318‐14 Note Description 2.1 2.2 ‡ Heading: Code notation A2 A2 ~ Revised notation f'cr ‐‐‐ ~ Reference to ACI 301 replaced this notation ft ft ~ Revised notation Mslab …
CHAPTER 13 BEAMS - American Concrete Institute
www.concrete.orgACI 318-14 Chapter 13 Code, Approved Version, Revised 2013-07-25 4 129 130 13.4 — Required strength 131 132 13.4.1 — General 133 134 13.4.1.1 — Required strength shall be calculated in accordance with the factored load 135 combinations defined in Chapter 7 and analysis procedures defined in Chapter 8. <~>
437R-19: Strength Evaluation of Existing Concrete Buildings
www.concrete.orgassessment of structural safety can be achieved with the infor- ... is particularly true for structures deteriorated from prolonged exposure to the environment or damaged in an extreme event, such as a fire, earthquake, or explosion. Similarly, there are no generally recognized criteria for ... (repair or strengthening) g) Structures that ...
Related documents
Chapter 3 Pre-Installation, Foundations and Piers - Oregon
www.oregon.govNew home installations must be anchored according the manufacturer’s installation instructions. Secondary installations may be anchored according to the manufacturer’s installation instructions, or according to Section 3-2.6 of this code. Certain earthquake resistant bracing systems may comply with this requirement. Flood Hazard Areas
DESIGN AND INSTALLATION GUIDE - Cemintel
www.cemintel.com.auflat, off the ground, properly supported on a level platform and protected from the weather. Care should be taken to avoid damage to edges, ends and surfaces. If sheets become wet, allow to dry thoroughly before fixing. Product Description Size Quantity Product Code Makita Plunge Saw Kit (1300W) includes 1400mm guide rail and bonus 165mm fibre ...
INSTALLATION GUIDE for corrugated roofing panel …
www.cranecomposites.comPanels may we washed with either mild detergent-type cleaners or by steam and high-pressure spray systems. Apply cleaners with sponge ... temperatures not below 60°F. installation guide for corrugated roofing panel installation ... level ground with good drainage, sunny area away from large trees, and close access to water and electric 2 ...
ICE MAKER INSTALLATION INSTRUCTIONS ... - KitchenAid
www.kitchenaid.comdrainage from all drains. The ideal installation has a standpipe with a 1¹⁄ 2" (3.81 cm) to 2" (5.08 cm) PVC drain reducer installed directly below the outlet of the drain tube as shown. You must maintain a 1" (2.54 cm) air gap between the drain hose and the standpipe. Do not connect the outlet end of the drain tube to a closed
Troubleshooting and Maintenance Guide for Residential ...
www.rainbird.comfor easy access in below ground situations. Once this valve is installed and tested, the valve at the meter may be left open for water usage inside the house. In freezing climates, your next step will be to install a manual drain valve so that the water can be drained from the pipes between the zone valves and the shut-off valve.
GENERAL NOTES HINGE POINT LINE - Wisconsin Department …
wisconsindot.govJul 13, 2018 · dimensions and installation instructions. the center of the upper 3 1 2" diameter hole on post number 3 through post 9 is to be flush with the ground line up to a maximum of 2" above ground line. wood blocks on posts numbered 3 through 9 may be adjusted up to 3" above the top of post. 9 f 6 6 sdd sdd 14b44 - 04a 14b44 - 04a
Guide to Trench Excavations (Shoring Support and Drainage ...
www.cedd.gov.hkfactors in the case of trench-related slope failures was found to be inadequate drainage provisions. In view of the above, this Guide emphasizes the deficiencies identified by the GEO/CED study, i.e. the need for adequate shoring support and drainage measures, and the need to comply strictly with site supervision requirements and site safety
DECKING INSTALLATION INSTRUCTIONS
images.thdstatic.comSleeper installation: Minimum joist height is 1.5 in. (38.1 mm), installed level, in the direction of water runoff and directly to a solid sub- structure. Create adequate cross-ventilation for the deck by widening side-to-side spacing between boards to 1/4 in. (6.4 mm) with a
Related search queries
Installation, Oregon, Systems, DESIGN AND INSTALLATION GUIDE, Ground, Guide, INSTALLATION GUIDE for corrugated roofing panel, Below, Installation guide for corrugated roofing panel installation, Drainage, KitchenAid, Troubleshooting and Maintenance Guide, Below ground, DECKING INSTALLATION INSTRUCTIONS