Residential Deck Construction Guide
1. Lumber shall be preservative-treated, southern pine fir, grade #2 or better. 2. Lumber in contact with the ground shall be rated as “ground-contact.” Not all treated lumber is rated for ground contact. 3. Concrete in footings shall have a minimum compressive strength of 3,000 PSI. 4. Nails shall be threaded, ring-shanked or annular grooved.
Download Residential Deck Construction Guide
Information
Domain:
Source:
Link to this page:
Documents from same domain
How well do you know Canada? Invite your family or friends ...
www.collingwood.caInvite your family or friends to test their ... Halifax who took a stand for racial equality in a rural Nova Scotia movie theatre. It was 1946, and Viola ... His investments in Montreal helped to transform the city from a colonial outpost to a cosmopolitan centre. 7. ...
Related documents
Prescriptive Residential Wood Deck Construction Guide
www.awc.orgUse Table 2 to determine allowable joist span, L J, based on lumber size and joist spacing. Joist span, L, must be less than or equal to allowable joist span, L J. Overhang length is the lesser of allowable overhang, L O, or one fourth the joist span, L/4. See Figure 1 and Figure 2 for joist span types.
MONTGOMERY COUNTY RESIDENTIAL TYPICAL DECK …
www.montgomerycountymd.govAll deck lumber shall be #2 Southern Pine or better. All lumber shall be pressure-treated –with an ... fourth of the actual adjacent joist span or the maximum cantilevered length shown on table 3. Whichever is less. The ends of joists shall have not less than 1 ½” bearing on wood or metal.
TABLE #2 JOIST LENGTH TREATED LUMBER T A C N G
www.franklinwi.govtable #2 joist length treated lumber 6' 7' 8' 9' 10' 11' 12' 13' 14' 15' 16' 4' joist size 2x6 24"oc 2x6 16"oc 2x8 24"oc 2x6 16"oc 2x8 24"oc 2x8 16"oc 2x10 24"oc
Prescriptive Residential Wood Deck Construction Guide
www.awc.orgUse Table 2 to determine allowable joist span, LJ, based on lumber size and joist spacing. Joist span, L, must be less than or equal to allowable joist span, LJ. Overhang length is the lesser of allowable overhang, LO, or one fourth the joist span, L/4. See Figure 1 …
Fairfax County Typical Deck Details
www.fairfaxcounty.govNot all treated lumber is rated for ground contact. 3. Concrete in footings shall have a minimum ... joist span length does not include overhangs. • The joists’ design is based on spacing, size and span length. Use TABLE 2 to determine joist size and the corresponding maximum allowable overhang. Note: the overhang dimension shall never ...
Specifier's Guide for Parallam Plus PSL
www.northeastco.comTrus Joist ® Parallam Plus PSL Specifier's Guide TJ-7102 |14June 20 3 pRoduCT FeaTuReS and SizeS in order for parallam® plus pSl to perform as described, the product must maintain its original cross section. parallam plus® beams, headers and columns may be cut to length, but must not be resawn in depth or thickness.
1. Revise Table R602.3(1) as follows - in
secure.in.gov28 2” subfloor to joist or girder, blind and face nail 2-16d (3½” × 0.135”) - 29 2” planks (plank & beam – floor & roof) 2-16d (3½” × 0.135”) at each bearing 30 Built up girders and beams, 2-inch lumber layers 10d (3" x 0.128") Nail each layer as follows: ... Up to 50 feet when length of required bracing per Table R602.10.3(3 ...
TREATED LAMINATED VENEER LUMBER
pacificwoodtech.comFeb 17, 2021 · PWT Treated LVL 2.0 850 2.0 650 LP SolidGuard LSL 1.35 750 1.35 685 TJ StrandGuard / TimberStrand LSL 1.3 710 1.3 670 #2 DF (treated-incised) 1.5 625 1.5 625 #2 SYP (treated) 1.4 565 1.4 565 #2 Hem-Fir (treated incised) 1.2 405 1.2 405 SIZES AVAILABLE 1½ x 3½ 1½ x 5½ 1½ x 7¼ 1½ x 9¼ 1½ x 11¼ PWT Treated LVL Stair Stringers
Maximum Joist Spacing for Decks - CKCOG
www.ckcog.comDetermine the decking board thickness and direction to determine joist spacing. (Table 1:1) 2. Decide whether the joists will cantilever over or not. Then using the lumber size of joists and the joist spacing, determine if you are within the maximum allowable joist span. (Table 1:2 or Table 1:3) 3. Using the beam span table, select your beam ...