Rigging Safety Guide - MCAA
• Prevent rigging/lifting related injuries; • Prevent damage to equipment, materials and property; and • Perform their rigging responsibilities more effectively. This guide is intended to help the user include safety in the planning and actual practice of rigging mechanical industry equipment and materials for lifting operations.
Download Rigging Safety Guide - MCAA
Information
Domain:
Source:
Link to this page:
Documents from same domain
ADDITIONAL NATIONAL AGREEMENTS ADMINISTERED BY …
www.mcaa.orgThe General Presidents’ Project Maintenance Agreement (GPPMA) was revised as of July 2005 and the Interpretations/Bulletins have been revised as of September 2010.
2017 Regional Training Course Catalog - MCAA | Support and ...
www.mcaa.orgThe OptiView Control Center plus preventive maintenance and system checkout procedures are also addressed along with a hands-on teardown and rebuild of a YK centrifugal compressor.
MCAA Guide to Pressure Testing Safety
www.mcaa.orgSafely pressure testing piping systems can be challenging at times. However, much of the time the procedures are routine and can be accomplished with minimal risk to workers.
MCAA Management Methods Manual - Preparing for a …
www.mcaa.orgPRE-AUDIT Prior to receiving the audit notification from the state or local government, you should already have a plan on how to effectively defend yourself.
General Welding Guidelines - MCAA
www.mcaa.orgGeneral. The instructions contained in this portion of the guidelines provide additional information to the welder concerning variables, which are not usually addressed by the Welding
BUILDING SERVICES PIPING CONSTRUCTION
www.mcaa.orgWELDERS? B31.9 permits "interchange" of welders among contractors after they have been properly qualified by one contractor provided the welder’s new employer accepts responsibility for qualification performed by the other contractor. By interchanging qualified welders, contractors do not have to repeat the time-consuming testing of workers.
Toolbox Safety Talks for Fabrication Shops
www.mcaa.orgToolbox Safety Talks for Fabrication Shops Mechanical Contractors Association of America, Inc. 1385 Piccard Drive Rockville, MD 20850 800-556-3653 • www.mcaa.org
MATERIAL COST ESCALATION PACKAGE
www.mcaa.orgabove what was originally forecast for 2021. Steel prices at mills in the United States are up 60% to 100% in the last 6 months, affecting the cost of structural steel, steel joists, reinforcing steel, metal deck, stairs and rails, metal panels, metal ceilings, wall studs, door frames, canopies, steel duct, steel pipe and
General Brazing Guidelines - MCAA
www.mcaa.orgThese General Brazing Guidelines are intended to pro-vide background information and supplementary in-structions to contractors and their brazers who are us-ing National Certified Pipe Welding Bureau Welding (NCPWB) Brazing Procedure Specifications (BPSs). This document is divided into three parts: Mandatory
Understanding Bend Tests - MCAA
www.mcaa.orgQualification test plates can be prepared with the weld groove preparation parallel to the direction of rolling. The length of the bend specimens extracted from such a test plate will be perpendicular to the rolling direction (Figure 2). This means when the specimen is bent, straining is perpendicular
Related documents
Part 6 Cranes, Hoists and Lifting Devices - Alberta
open.alberta.caExcept as described in subsection 59(4), all lifting devices with a rated capacity of 2000 kilograms or more are subject to the requirements of this Part. A lifting device is a device used to raise or lower materials or an object. A crane is a lifting device that can move a load horizontally. Examples of cranes include the following:
Ordinary Lift Planning and Control Form
www-group.slac.stanford.eduRigging Sketch or Photo of Rigged Item (Include all information required to determine that the load is properly rigged and that appropriate rigging ge ar is selected. Include, Include, as applicable, sling angles, eye bolt orientation, padding points, center of gravity, type of sling hitch, and any other pert inent information.)
Hoisting & Rigging Fundamentals - Energy
www.energy.govINTRODUCTION HOISTING AND RIGGING PROGRAM Safety should be the first priority when performing lifting operations. An understanding of the capabilities and limitations of the equipment will support this. The safety policy “lf It‘s Not Safe, Don‘t Do It” is important not only for your safety, but the safety of your coworkers.
Working at height - HSE
www.hse.gov.ukHealth and Safety Executive Working at height Page 2 of 7 make sure you don’t overload or overreach when working at height; take precautions when working on or near fragile surfaces; provide protection from falling objects; consider your emergency evacuation and rescue procedures. Who do the Regulations apply to? If you are an employer or you control work at …
Health and Safety (H&S) Manual for Contractors
www.nec.comradius; over an occupied structure or public street; of lifting an item of high value or long replacement time. Dynamic Risk Assessment - The continuous process of identifying hazards, assessing risk, taking action to eliminate or reduce risk, monitoring and reviewing, in the rapidly changing circumstances of an operational incident.
Information Sheet: High risk work licensing for vehicle ...
www.safeworkaustralia.gov.authe lifting gear can be pre-determined by a . competent person and set out in a safe work lifting procedure, for example where high volume repetitive lifting occurs. A competent person includes a dogger, rigger or an engineer experienced in designing safe work lifting procedures. A safe work lifting procedure is a documented
Split System Cooling Units - Trane
www.trane.com• Rigging tests include lifting a unit into the air and letting it drop one foot, assuring that the lifting lugs and rails hold up under stress. Features and Benefits. 8 SS-PRC003-EN Application Considerations Low Ambient Cooling As manufactured, these units can operate to …