SCOPE - James Hardie
Applying James Hardie® Siding over Continuous TECHNICAL BULLETIN Insulation and Non-Nailable Substrates SEPTEMBER 2014 #19 The guidance and instructions provided in this technical bulletin are valid for and applicable to James Hardie® products only. James
Download SCOPE - James Hardie
Information
Domain:
Source:
Link to this page:
Documents from same domain
Page 1 10 231 S. LaSalle Street, Suite 2000 Chicago, IL ...
www.jameshardie.comPage 1 of 10 Date of Issue: 06/01/15 231 S. LaSalle Street, Suite 2000 Chicago, IL 60604 SAFETY DATA SHEET Section 1. Identification Product Identifier: Exterior Fiber-Cement (Medium Density) – Includes all Generation 6 HZ5 and HZ10 products with the following product names: HardiePlank® lap
Fastening Tips for HardiePlank Lap Siding TECHNICAL ...
www.jameshardie.comIMPORTANT: Failure to install and fi nish this product in accordance with applicable building codes and James Hardie written application instructions
30-Year Limited Warranty - James Hardie
www.jameshardie.com1-800-9-HARDIE 10901 Elm Avenue Fontana, CA 92337 30-Year Limited Warranty HardiePlank® HZ5® Lap Siding, HardiePanel® HZ5® Vertical Siding, HardieShingle® HZ5® Siding, HardieSoffit® HZ5® Panels 1. LIMITED WARRANTY. James Hardie Building Products
Finishing James Hardie TECHNICAL BULLETIN Siding …
www.jameshardie.comand is not recommended. For care & maintenance instructions for ColorPlus and primed products refer to James Hardie Tech Bulletin#20 at www.jamehardie.com If a pressure washer is to be used, use wide fan tips only, at low pressures under 1,500 psi and at safe distances. Keep fan nozzle no closer than 6’ to wall. Exercise extreme caution.
NO CAULK - James Hardie
www.jameshardie.comJames Hardie also DOES NOT recommend applying caulk to the horizontal overlap between siding planks (see Figure 2). Joint flashing Butt Joint & Horizontal Lap Treatment JUNE 2014 James Hardie does not recommend caulking butt joints or the horizontal overlaps Joint Flashing 6 in. (152.4 mm) wide,
ICC-ES Legacy Report NER-405* Reissued April 2004
www.jameshardie.comICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as
Cut time. Not Quality. - James Hardie
www.jameshardie.com®• HardieBacker Cement Board with HydroDefense™ Technology has internal ... (2015/18 IRC P2709, 2015 IPC 417.5 and/or 2018 IPC 421.5). Completed liners shall be flood tested in accordance with code.
Related documents
english Language arts Literacy in History/social studies ...
www.corestandards.orgstudies, and science, mathematics, and technical subjects, with the ELA texts further subdivided into stories, drama, poetry, and informational texts. (The history/social studies texts also include some arts-related texts.) Citations intro-duce each excerpt, and additional citations are included for texts not excerpted in the appendix.
Foamular 250 XPS Insulation Product Data Sheet
www.owenscorning.comTechnical Information • FOAMULAR® 250 XPS insulation is a non-structural material and must be installed on framing that is independently braced and structurally adequate to meet required construction and service loading conditions. • FOAMULAR® 250 XPS insulation can be exposed to the exterior during normal construction cycles. During that ...
Extruded Polystyrene (XPS) Rigid Foam Insulation Product ...
www.owenscorning.comExtruded Polystyrene (XPS) Rigid Foam Insulation • Provides a weather resistant barrier (when joints are sealed) to enhance the building resistance to air and moisture penetration. Technical Information This product is combustible. A protective barrier or thermal barrier is required as specifi ed in the appropriate building code.
Understanding Fault Technical Report - NREL
www.nrel.gov• Insulation breakdown caused by system overvoltages from lighting strikes and switching surges, improper manufacturing, improper installation, and aged or polluted insulation. • Mechanical issues such as animal contact, tree contact, vehicle collisions, wind, snow, ice, contamination, vandalism, and major natural disasters.
CompactLogix 5380, Compact GuardLogix 5380, and ...
literature.rockwellautomation.comTechnical Data Original Instructions CompactLogix 5380, Compact GuardLogix 5380, and CompactLogix 5480 Controllers Specifications Bulletin 5069 Topic Page ... 300V (continuous), Basic Insulation Type, Ethernet to Backplane 300V (continuous), Double Insulation Type, Ethernet to MOD Power
Cat5e Cable - Farnell
www.farnell.comMinimum elongation at break of the insulation ≥ 100 % Minimum elongation at break of the sheath ≥ 100 Tensile strength of sheath < 9 MPa Mechanical characteristics Low frequency and D.C. (at 20°C) Specification Unit Maximum operating voltage (for all temperatures cable is intended to be used) 72 V dc
Technical Guide No. 102
library.e.abb.comThis technical guide addresses the extra voltage stress on the motor’s insulation system, related to the square wave pulses comprising the PWM AFD’s voltage ... Insulation is required wherever there is a difference of electrical potential between two (2) conductors. Turn-to-turn insulation prevents one (1) turn of a
TRYMER 2000XP - Johns Manville
www.jm.comPOLYISOCYANURATE FOAM INSULATION DESCRIPTION Trymer® 2000XP insulation is a closed-cell insulation that features improved dimensional stability over a wider range of temperatures than standard polyurethane insulation. Trymer 2000XP insulation is polyurethane modified polyisocyanurate (PIR) cellular plastic. The rigid insulation is supplied in the