SCOPE - James Hardie
Note: We recommend performing a small siding mockup prior to installation to ensure the fastening practice and/or fastening tools are properly adjusted. Fasteners must be installed in a manner to avoid overdriving, yet snug enough to remove gaps between the connected parts.
Download SCOPE - James Hardie
Information
Domain:
Source:
Link to this page:
Documents from same domain
Page 1 10 231 S. LaSalle Street, Suite 2000 Chicago, IL ...
www.jameshardie.comPage 1 of 10 Date of Issue: 06/01/15 231 S. LaSalle Street, Suite 2000 Chicago, IL 60604 SAFETY DATA SHEET Section 1. Identification Product Identifier: Exterior Fiber-Cement (Medium Density) – Includes all Generation 6 HZ5 and HZ10 products with the following product names: HardiePlank® lap
Fastening Tips for HardiePlank Lap Siding TECHNICAL ...
www.jameshardie.comIMPORTANT: Failure to install and fi nish this product in accordance with applicable building codes and James Hardie written application instructions
30-Year Limited Warranty - James Hardie
www.jameshardie.com1-800-9-HARDIE 10901 Elm Avenue Fontana, CA 92337 30-Year Limited Warranty HardiePlank® HZ5® Lap Siding, HardiePanel® HZ5® Vertical Siding, HardieShingle® HZ5® Siding, HardieSoffit® HZ5® Panels 1. LIMITED WARRANTY. James Hardie Building Products
Finishing James Hardie TECHNICAL BULLETIN Siding …
www.jameshardie.comand is not recommended. For care & maintenance instructions for ColorPlus and primed products refer to James Hardie Tech Bulletin#20 at www.jamehardie.com If a pressure washer is to be used, use wide fan tips only, at low pressures under 1,500 psi and at safe distances. Keep fan nozzle no closer than 6’ to wall. Exercise extreme caution.
NO CAULK - James Hardie
www.jameshardie.comJames Hardie also DOES NOT recommend applying caulk to the horizontal overlap between siding planks (see Figure 2). Joint flashing Butt Joint & Horizontal Lap Treatment JUNE 2014 James Hardie does not recommend caulking butt joints or the horizontal overlaps Joint Flashing 6 in. (152.4 mm) wide,
ICC-ES Legacy Report NER-405* Reissued April 2004
www.jameshardie.comICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as
Cut time. Not Quality. - James Hardie
www.jameshardie.com®• HardieBacker Cement Board with HydroDefense™ Technology has internal ... (2015/18 IRC P2709, 2015 IPC 417.5 and/or 2018 IPC 421.5). Completed liners shall be flood tested in accordance with code.
Related documents
COMMON HAND TOOLS AND THEIR PROPER USE
www.dcfpnavymil.orgCOMMON HAND TOOLS Simultaneous use of hand tools and machines. Machine shop work is usually understood to include all cold metal work in which a portion of the metal is removed, either by power-driven or hand tools, to make the piece of the required shape and size. However, there are some branches of cold metal work, such
Hybrid Wood and Steel Details– Builder’s Guide
www.huduser.govHybrid Wood and Steel Details–Builder’s Guide Preface The NAHB Research Center, the U.S. Department of Housing and Urban Development (HUD), and the Steel Framing Alliance have worked cooperatively to introduce cold-formed
Health and Safety CN Drilling with hand- held rotary power ...
www.hse.gov.ukConstruction: Silica CN3 Drilling with hand-held rotary power tools n using cordless extraction attached to the drill, ie an M or H class extraction system correctly attached to an on-tool adaptor together with spare waste collection bags where needed. For drilling as a main activity 3 Choose the correct drill and bit(s).
REQUIREMENTS FOR THREADED FASTENING SYSTEMS IN …
standards.nasa.govThis Standard establishes criteria for ensuring the integrity of threaded fastening systems in launch and space vehicles and their associated equipment. Requests for information, corrections, or additions to this Standard should be submitted via
Tremco TPO Installation Manual
www.tremcoroofing.comHand Tools and Power Tools: ... For roof membrane fastening, stress plates shall be two inch (2 3/8”) O.D. barbed round, G‐90 hot dipped galvanized stress plates with a recessed .260” I.D. center hole as ...
Inserts - STANLEY® Engineered Fastening
www.stanleyengineeredfastening.comManual Tools Heli-Coil offers a complete line of tooling together with a full array of STI taps, gages and tang break-off tools. For production runs, prototype work, salvage and repair, Heli-Coil offers a range of installation and extraction tools for both tanged and tangless inserts to complete the needs of your application. Power Tools
Table of Contents - STANLEY® Engineered Fastening
www.stanleyengineeredfastening.comthread inserts, cutting tools, and thread gages. Spiralock products solve fastening issues in a variety of applications across a wide range of industries, including aerospace/ defense, electronics, medical, automotive, truck, farm and construction, oil and gas …
Electric Nutrunners - Atlas Copco
www.atlascopco.comThe Tensor range of electric assembly tools covers all station and assembly line re-quirements for safety critical and quality critical fastening applications. At Atlas Copco we have a proud legacy of putting the operator first and we continuously improve the ergonomic features on each new generation of Tensor tools. Tensor is also one of the