SCOPE - James Hardie
Foam Sheathing Coalition) installation guidance (from Step 7 above). • The fastener must fully engage the framing or stud. • To help the furring installer know where the framing members are so as to attach the furring to the framing, o Transfer the frame layout directly from wall framing to each attachment of rigid foam insulation or
Download SCOPE - James Hardie
Information
Domain:
Source:
Link to this page:
Documents from same domain
Page 1 10 231 S. LaSalle Street, Suite 2000 Chicago, IL ...
www.jameshardie.comPage 1 of 10 Date of Issue: 06/01/15 231 S. LaSalle Street, Suite 2000 Chicago, IL 60604 SAFETY DATA SHEET Section 1. Identification Product Identifier: Exterior Fiber-Cement (Medium Density) – Includes all Generation 6 HZ5 and HZ10 products with the following product names: HardiePlank® lap
Fastening Tips for HardiePlank Lap Siding TECHNICAL ...
www.jameshardie.comIMPORTANT: Failure to install and fi nish this product in accordance with applicable building codes and James Hardie written application instructions
30-Year Limited Warranty - James Hardie
www.jameshardie.com1-800-9-HARDIE 10901 Elm Avenue Fontana, CA 92337 30-Year Limited Warranty HardiePlank® HZ5® Lap Siding, HardiePanel® HZ5® Vertical Siding, HardieShingle® HZ5® Siding, HardieSoffit® HZ5® Panels 1. LIMITED WARRANTY. James Hardie Building Products
Finishing James Hardie TECHNICAL BULLETIN Siding …
www.jameshardie.comand is not recommended. For care & maintenance instructions for ColorPlus and primed products refer to James Hardie Tech Bulletin#20 at www.jamehardie.com If a pressure washer is to be used, use wide fan tips only, at low pressures under 1,500 psi and at safe distances. Keep fan nozzle no closer than 6’ to wall. Exercise extreme caution.
NO CAULK - James Hardie
www.jameshardie.comJames Hardie also DOES NOT recommend applying caulk to the horizontal overlap between siding planks (see Figure 2). Joint flashing Butt Joint & Horizontal Lap Treatment JUNE 2014 James Hardie does not recommend caulking butt joints or the horizontal overlaps Joint Flashing 6 in. (152.4 mm) wide,
ICC-ES Legacy Report NER-405* Reissued April 2004
www.jameshardie.comICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as
Cut time. Not Quality. - James Hardie
www.jameshardie.com®• HardieBacker Cement Board with HydroDefense™ Technology has internal ... (2015/18 IRC P2709, 2015 IPC 417.5 and/or 2018 IPC 421.5). Completed liners shall be flood tested in accordance with code.
Related documents
Thermal Insulation Materials Made of Rigid Polyurethane Foam
highperformanceinsulation.euThermal insulation with rigid polyurethane foam (PUR/PIR) conserves resources, saves energy and has no significant emission to the environment. Rigid polyurethane foam (PUR/PIR) is the right investment for the future as it: offers optimal, long-life insulation with no drawbacks, maintenance or
Construction Guide: Energy Efficient, Durable Walls
www.energy.gov4" RIGID FOAM INSULATION DRYWALL 2X6 WALLS - CORNERS. High Performance Walls || CZ 3-5 13 Framing Details for Cladding Systems That Require Additional Framing for Trim TRIM NAILER FILLER or CONTINUOUS SHEATHING 16d BOX @ 12" o.c. APPROVED CLIP DRYWALL FILLER or CONTINUOUS SHEATHING 16d BOX @ 12" o.c. 4" RIGID FOAM …
AP Foil-Faced - Johns Manville
www.jm.compolyisocyanurate foam core bonded on each side to a foil facer. One side has a reflective foil facer and the other side has a white non-reflective foil facer to suit your building needs. Polyiso provides one of the highest R-values per inch of any rigid insulation (R-6.0 at 1 inch).
NIGP Commodity Codes (18th Edition)
app.ocp.dc.govinsulation, pipe fitting, pvc, white, w/glass fiber inserts, tees 010-81-38 INSULATION, PIPE FITTING, FIBERGLASS, TWO (2) PIECE ELBOWS, 90 DEGREE ELL, TWO PIECES EQUAL ONE
DuPont Styrofoam Brand Scoreboard XPS Foam Insulation
www.dupont.comWARNING: Rigid foam insulation does not constitute a working walkable surface or qualify as a fall protection product. Building and/or construction practices unrelated to building materials could greatly affect moisture and the potential for mold formation.
Insulation Fact Sheet
www.energystar.govRigid insulation is made from fibrous materials or plastic foams and is produced in board-like forms and molded pipe coverings. These provide full coverage with few heat loss paths and are often able to provide a greater R-value where space is limited. Such boards may be faced with a reflective foil that reduces heat flow when next to an air space.
Pipe Insulation (Hot & Cold) Material Selection & Application
local.ecollege.iePhenolic Foam Rigid closed cell foamed insulation manufactured from phenolic resin. Insulating Cement Insulating and finishing cements are a mixture of various insulating fibres and binders with water and cement, to form a soft plastic mass for application on irregular surfaces. Insulation values are moderate. Cements may be applied to
DuPont Styrofoam Brand Square Edge XPS Foam Insulation
www.dupont.comWARNING: Rigid foam insulation does not constitute a working walkable surface or qualify as a fall protection product. Building and/or construction practices unrelated to building materials could greatly affect moisture and the potential for mold formation.
Guide to Insulation Sheathing - Energy
www1.eere.energy.govFor unfaced insulation, the permeability is a function of the material thickness. In general most product manufacturers list the permeance of the material based on a thickness of 1 inch. Increasing or decreasing the thickness of the material will affect the permeance. This can become an issue when using XPS foam insulation.