SCOPE - James Hardie
Hardie Building Products Inc. makes no warranty or representation with respect to use of the information contained herein for any use other than with James Hardie® products, including but not limited to use with fi ber cement siding products made by others or siding products made of other materials.
Download SCOPE - James Hardie
Information
Domain:
Source:
Link to this page:
Documents from same domain
Page 1 10 231 S. LaSalle Street, Suite 2000 Chicago, IL ...
www.jameshardie.comPage 1 of 10 Date of Issue: 06/01/15 231 S. LaSalle Street, Suite 2000 Chicago, IL 60604 SAFETY DATA SHEET Section 1. Identification Product Identifier: Exterior Fiber-Cement (Medium Density) – Includes all Generation 6 HZ5 and HZ10 products with the following product names: HardiePlank® lap
Fastening Tips for HardiePlank Lap Siding TECHNICAL ...
www.jameshardie.comIMPORTANT: Failure to install and fi nish this product in accordance with applicable building codes and James Hardie written application instructions
30-Year Limited Warranty - James Hardie
www.jameshardie.com1-800-9-HARDIE 10901 Elm Avenue Fontana, CA 92337 30-Year Limited Warranty HardiePlank® HZ5® Lap Siding, HardiePanel® HZ5® Vertical Siding, HardieShingle® HZ5® Siding, HardieSoffit® HZ5® Panels 1. LIMITED WARRANTY. James Hardie Building Products
Finishing James Hardie TECHNICAL BULLETIN Siding …
www.jameshardie.comand is not recommended. For care & maintenance instructions for ColorPlus and primed products refer to James Hardie Tech Bulletin#20 at www.jamehardie.com If a pressure washer is to be used, use wide fan tips only, at low pressures under 1,500 psi and at safe distances. Keep fan nozzle no closer than 6’ to wall. Exercise extreme caution.
NO CAULK - James Hardie
www.jameshardie.comJames Hardie also DOES NOT recommend applying caulk to the horizontal overlap between siding planks (see Figure 2). Joint flashing Butt Joint & Horizontal Lap Treatment JUNE 2014 James Hardie does not recommend caulking butt joints or the horizontal overlaps Joint Flashing 6 in. (152.4 mm) wide,
ICC-ES Legacy Report NER-405* Reissued April 2004
www.jameshardie.comICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as
Cut time. Not Quality. - James Hardie
www.jameshardie.com®• HardieBacker Cement Board with HydroDefense™ Technology has internal ... (2015/18 IRC P2709, 2015 IPC 417.5 and/or 2018 IPC 421.5). Completed liners shall be flood tested in accordance with code.
Related documents
Florida Product Approval HardiePlank Lap Siding
www.floridabuilding.orgHardie® Siding Products” at www.JamesHardie.com. • DO NOT use stain on James Hardie® products. WARNING: AVOID BREATHING SILICA DUST James Hardie ® products contain respirable crystalline silica, which is known to the State of California to cause cancer and is considered by IARC and NIOSH to be a cause of cancer from some occupational ...
Design Manual - James Hardie
www.jameshardie.co.nzFigure 1: Vertical junction between Linea™ Weatherboard and James Hardie flat sheet cladding Figure 2: Vertical junction between Linea™ Weatherboard and James Hardie flat sheet cladding 4 James Hardie Cladding Junction Details Design Manual November 2016 New Zealand Flexible underlay Linea™ Weatherboard Scriber 60 x 3.15mm jolt head
HardieTrim Boards Products Description - James Hardie Pros
www.jameshardiepros.com32 HardieTrim® Boards Products Description HardieTrim® boards come finished with either the PrimePlus® factory primer and sealer or with ColorPlus® Technology. The ColorPlus® coating is a factory-applied, oven-baked finish available on a variety of James Hardie® siding and trim products. See your local dealer for details and availability of products, colors, and accessories.
HardieTrim Boards - Installation Instructions
www.buildsite.comJames Hardie recommends the use of quality, hot-dipped galvanized nails. James Hardie is not responsible for the corrosion resistance of fasteners. Stainless steel fasteners are recommended when installing James Hardie products near the ocean, …
HardiePanel Vertical Siding - James Hardie Pros
www.jameshardiepros.comHardie technical sales representative for assistance. James Hardie makes no representation or warranty that adopting a particular cutting practice will assure your compliance with OSHA rules or other applicable laws and safety requirements. 1 Water-resistive Barrier and drainage requirements as defined by building code.
Linea Weatherboard Installation Guide
static-content-prod.jameshardie-digital.com.auJames Hardie™ external cladding and roofs, decks, paths, steps and driveways. Adjacent finished grade must slope away from the building in accordance with local building codes, typically a minimum slope of 50mm minimum over the first metre. Do not install external cladding such